background image

1. Setup Procedure

 

 
 

Express5800/R320e-E4, R320e-M4, R320f-E4, R320f-M4  Installation Guide (VMware) 

67

Chapter 1  Installing OS 

1.14.2 

 

System information 

 Run 

POST. 

1.

While the following message appears, press 

F4

 

 Press <F2> SETUP, <F4> ROM Utility, <F12> Network

 

 

 

When POST completes, the keyboard selection menu appears. 

2.

If you select your keyboard layout, the following menu will appear. 

 

 Choose 

Maintenance Utility

 – 

System Information Viewer

 – 

Display System Information

 – 

3.

System Information

. Write down the following system information. 

    “Product Name” 
    “FR Number” 
    “Serial Number” 

 Press 

ESC

 several times until the following menu appears. 

4.

 

 

1.14.3 

 

BMC Configuration 

 Choose 

BMC Configuration

 – 

BMC Configuration

. Write down the BMC Configurations that have 

1.

changed. 
< Example > 
    “Network : CPU/IO module0”-“IPvx Property” 
    “Network : CPU/IO module1”-“IPvx Property” 
    “User Management”-“User Account” 

 Press 

ESC

 several times until the following menu appears. 

2.

 

 

Choose “Exit” to exit. 

3.

 

Off-line TOOL MENU 

Maintenance Utility 
BMC Configuration 
Exit 

Off-line TOOL MENU 

Maintenance Utility 
BMC Configuration 
Exit 

Off-line TOOL MENU 

Maintenance Utility 
BMC Configuration 
Exit 

Summary of Contents for EXP320R

























































































Reviews: