NEC EXP320R Installation Manual Download Page 22

Page: 22 / 88

1. Setup Procedure

Express5800/R320e-E4, R320e-M4, R320f-E4, R320f-M4 Installation Guide (VMware)

Chapter 1 Installing OS

Among the parameters, choose "Enabled" and press

Enter

The current display of the configuration for

PCI Slotx Option ROM

will be changed to “Enabled”

Select an item other than

PCI Slot x Option ROM

for the PCI slot in which Fibre Channel card is

10.

installed, and press

Enter

. Select

Disabled

from the parameters displayed, and press

Enter

. Repeat

these steps for all items other than

PCI Slot x Option ROM

for the PCI slot in which Fibre Channel

card is installed

Make sure that

PCI Slot x Option ROM

for the PCI slot in which Fibre Channel card is installed shows

11.

Enabled

, and all other items show

Disabled

This is the end of steps for enabling Fibre Channel card.

Check the settings of XHCI Mode. Press [ESC] key two times to display the top of the Advanced

12.

menu.

Move the cursor onto "USB Configuration" and press

Enter

13.

Confirm that [XHCI Mode] is set to [Auto]. If not, set the value to [Auto].

14.

It continues to disable Legacy memory copy Function and OC boot monitoring Function.

15.

Proceed to "Chapter 1 (1.5 Disabling Legacy memory copy Function)" to continue configuring.

Summary of Contents for EXP320R

























































































Search results

Summary of Contents for EXP320R

Reviews:

Brands by name

Popular brands

NEC EXP320R, Installation Manual

Search results

Summary of Contents for EXP320R

Reviews:

Brands by name

Popular brands