background image

Warranty        21

Warranty Period

Navien products come with a limited warranty covering labor, 
parts and the heat exchanger. The following warranty periods 
begin to run from the date of original installation. The date of 
original installation must be provided to Navien, and upon request, 
proof of the original installation date must also be provided to 
Navien. When the product is installed in a new construction, the 
commencement date shall be dated upon which the end-user 
takes title to the property.

APPLICABLE WARRANTY PERIOD

Heat 

Exchanger

All other 

parts and 

components

Labor

Residential

15 years

5 years

1 year

Commercial

10 years

3 years

1 year

Warranty Claim Procedures

To obtain warranty repair service, the end user or homeowner 
must contact the original installer of your Navien product. If the 
original installer cannot be identified, the end user or homeowner 
may contact Navien’s Technical Administration Department at  

(800) 519-8794

. Proof of purchase is required to obtain warranty 

service. 

Warranty Service

At its option, Navien will replace the defective component (part(s) 
or heat exchanger), in accordance with the terms of this Limited 
Warranty, if it fails in normal use and service during the applicable 
warranty period identified above. The replacement component 
must be Navien original factory component. Navien, at its sole 
discretion, may replace the product with a new or refurbished 
product of comparable quality and design. The replacement 
component or product will be warranted only for the unexpired 
portion of the original component’s applicable warranty period. 
Payment for labor in completing the warranty service is subject 
to Navien’s prior written approval and shall be subject to Navien’s 
schedule of approved labor allowances.

LIMITED WARRANTY NAVIEN, INC.

Summary of Contents for NHB-110

























Reviews: