background image

 

importAnt SAfety precAutionS

13.  Never position the treadmill with the back end (direction of 

belt travel) facing a wall or any other objects such as furniture 
or other pieces of fitness equipment. Failure to do so can 
prevent safe exit of the treadmill in an emergency situation 
such as falling. allow a minimum of 79 inches (2 meters) 
behind the treadmill and 20 inches (.5 meters) on each side. 

14.  Before each use of this equipment, check the power cord, 

plug, plug receptacle and outlet for signs of damage. If any of 

them appears frayed, loose, worn, or otherwise faulty, or if 
the insulation appears worn or cracked, do not operate the 
machine. Position the treadmill so that the wall plug is visible 

and accessible. If the power cord is damaged, it must be 
replaced with a power cord from Nautilus, Inc. 

15.  to avoid potential safety and electrical problems, replace with 

manufacturers’ specified parts only. 

16.  always disconnect the treadmill from the power outlet before 

cleaning, maintaining, servicing, or removing the motor cover. 

17.  this equipment is classified Class I, type B, ordinary 

equipment. Not protected against fluid ingress. rated for 
continuous operation. Do not operate this equipment in the 
presence of flammable anesthetic mixtures.

18.  Do not let liquid enter the display or motor/controller area. If 

liquid enters either area, the area(s) must be inspected and 
tested for safety by an approved technician before it can be 
used again. Do not place the treadmill near water or outdoors.  
Do not use the machine in damp or wet conditions.

19.  Increased risk due to leakage of electrical current may result if 

this equipment is not grounded properly. 

20. the treadmill must be on an appropriate, dedicated electrical 

circuit carrying 15 amps (110 Volt model) or 7 amps (220 Volt 

model). Nothing else should be connected to the circuit. Use 
of a surge protector is recommended.

21. Do not stand on treadmill motor cover or front trim cover.

22.   Parents and others in charge of children should be aware that 

children, because of  their natural play instinct and fondness for

 

experimenting, may be tempted to situations and behavior for 

which the equipment is not intended, with resulting damage to 
the equipment and injury to the children or others.  Children’s 

access to the equipment should therefore be controlled, and 

they should be instructed about the potential for personal injury 

and damage if they play with the equipment.

Failure to follow the conditions set forth below shall limit, to the 

extent allowed by law, Nautilus

®

 Inc. responsibility for the safety, 

reliability, and performance of this equipment.

•  Each user must read the Owner’s Manual in full before using 

the product. Each user must read, understand, and carefully 
follow all warnings, instructions, and procedures regarding 
the proper use of the treadmill and its accessories. 

•  Do not remove the treadmill motor covers: dangerous voltages 

are present. Components such as the motor, controller, and 
display are serviceable only by qualified service personnel.

•  the electrical wiring within the treadmill setting and the 

electrical installation of the treadmill must comply with the 
applicable local or provincial requirements.

•  the equipment must be used in accordance with the 

instructions for use.

•  For further information or instruction on use, maintenance 

or specifications, please contact your authorized Nautilus

®

 

retail Outlet. 

Summary of Contents for Sport Series

































Reviews: