manualshive.com logo in svg

Nautel NX300, Operation And Maintenance Manual

Share
Download
Nautel NX300 Operation And Maintenance Manual Download Page 91

NX300 Operations and Maintenance Manual

Operating the transmitter

Issue 3.0  2012-11-01

Page 2-73

•

Subnet Mask - 

Masks an IP address, and divides the IP address into network address and host 

address (normally set to 255.255.255.0)

•

Default Gateway - 

Defines the address of the network access point.

•

Default Nameserver - 

Address that identifies the DNS host

•

Alternate Nameserver- 

Redirects the name server

•

Port Number - 

Used to identify the senders and receivers of messages. Defaults to 3501.

NOTE:

 If the transmitter is connected to the Internet via a firewall, and remote access is 

required, the port number for external incoming connections that are to be routed to the 
transmitter MUST be the same as the port number that the transmitter listens to on the 
internal network.

•

Status -

 Identifies the network status (Running or Not Running). Running indicates the transmitter 

is successfully connected to the network. Not Running indicates the transmitter is not 
communicating on the network, possibly due to a disconnected cable, incorrect network settings, a 
malfunctioning network device, etc..

4. Press 

Apply

 to accept your entries.

Summary of Contents for NX300



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands