manualshive.com logo in svg

Nautel NX300, Operation And Maintenance Manual

Share
Download
Nautel NX300 Operation And Maintenance Manual Download Page 127

NX300 Operations and Maintenance Manual

Operating the transmitter

Issue 3.0  2012-11-01

Page 2-109

B+ Calibration

The 

B+ Calibration 

page (see 

Figure 2.84

) displays the measured B+ levels, the B+ Limit Setpoint 

(high voltage alarm level; nominally 420 V) and a calibration box. The B+ calibration value allows you 
to enter a measured B+ voltage to calibrate the B+ based on an externally measured B+ level. 

Figure 2.84: Factory Settings - B+ Calibration

WARNING: Factory settings are established at the factory and should not require any adjustment. 
These settings affect critical system protections. Making changes to these settings may void your 
warranty. Contact Nautel before making changes.

For future reference, record a parameter value before and after making a change.

Summary of Contents for NX300



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands