manualshive.com logo in svg

Native Instruments Traktor Kontrol Z2, Manual

Share
Download
Native Instruments Traktor Kontrol Z2 Manual Download Page 60

▪

HP VOLUME

 (headphone volume) knob: Use this knob to adjust the headphone volume

level on your Z2. This knob controls both the hard-wired headphone volume in the Z2 and
the headphone volume knob on the TRAKTOR software. Headphone volume output is off

when the knob is turned all the way to the left and it is at its fullest when the knob is
turned all the way to the right.

▪

CUE MIX

 (headphone cue mix) knob: This knob directly adjusts the cue mix. When it is

turned all the way to the left, the headphones will output the cue channel only. When the
knob is all they way to the right, it will output the master signal only. When the knob is at
the  center  position,  the  headphones  will  receive  a  blend  of  both  output  busses.  Fading

between the two positions will mix between the two signals.

▪

A

 and 

B

 (headphone channel cue) buttons: The two headphone cue buttons are located

just below the 

CUE MIX

 knob and control the pre-listen monitor function. When on, the

channel's audio is sent to the headphone bus so that you can monitor it. Pressing either
of these buttons toggles the pre-listen monitor function on and off on Decks A or B. If you
hold 

SHIFT

 while pressing either button, you can toggle this function on and off on Decks

C or D.

5.4.17 REL / INTL Buttons A and B

 

The Play mode buttons on the Z2.

If you are using Timecode records or CDs to control TRAKTOR, pressing either of the 

REL /

INTL

 buttons toggles the mode of the respective Deck between being controlled by the Time-

code medium (Scratch Control) and Internal Playback, where the timecode medium is being
ignored by TRAKTOR.
You can also start or stop Deck A or B by pressing 

SHIFT

 + 

REL / INTL

; this will also automati-

cally enable Internal Playback mode.

When you press 

SHIFT

 + 

REL / INTL

, the associated Deck will be forced into Internal Play-

back mode (regardless of the previous state) and the Deck will start playing if previously
stopped and will stop playing if previously playing.

TRAKTOR KONTROL Z2 Hardware Reference

Top Panel

 

TRAKTOR KONTROL Z2 - Manual - 60

Summary of Contents for Traktor Kontrol Z2






















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands