background image

©

 National Instruments Corporation

13

NI PXIe-4353 and TB-4353 Terminal Block Installation Guide

Figure 9.  

Removing NI SC Express Modules

Create a Simulated Device

To run examples without the hardware installed, use an NI-DAQmx simulated device. To create a 
simulated device in MAX:

1.

Launch MAX.

2.

Right-click 

Devices and Interfaces»Create New

.

3.

From the dialog, select 

Simulated NI-DAQmx Device or Modular Instrument

.

4.

Type 

4353

 in the text box at the top of the window.

5.

Select the device from the list provided.

6.

Click 

OK

.

Cold-Junction Compensation

Cold-junction compensation is the process of measuring the temperature of the screw terminal junction 
for the thermocouple and applying a representative compensating voltage to the voltage measured by 
the thermocouple channel. The accuracy of the cold-junction temperature measurement is a key part of 
the accuracy of the overall thermocouple temperature measurement. The TB-4353 is carefully designed 
to ensure high-accuracy cold-junction temperature measurements, under a variety of conditions; 
however, care must be taken to ensure the best possible accuracy. Refer to th

Minimizing Thermal 

Gradients

 section for guidelines to minimize thermal gradients that could impact the CJC accuracy. 

Refer to th

Specifications

 section for the CJC accuracy specifications.

1

Captive Screws (Use to remove modules.)

2

Front Panel (Do not use to remove modules.)

NI PXIe-1062Q

COOLING CLEARANCE AND F

AN FIL

TER MAINTENANCE REQ

UIRED

S

EE MANU

AL.

CO

OLING

 CLEAR

ANCE

 AND

 FA

N F

ILTE

R M

AIN

TEN

ANCE

 RE

QU

IRED

S

EE M

AN

UAL.

1

2

Summary of Contents for PXIe-4353





















Reviews: