background image

© National Instruments Corporation

|

3-9

MXI-Express x1 Series User Manual

3.

Observe the LED status on the PCI-8361, PCIe-8361/8362/8363, 
PXI-8360/8364/8367/8368, and PXIe-8360/8364/8367/8368 where applicable. A properly 
connected and powered up system should display a valid link and power status on 

all

 of 

these boards once the host PC is powered on. Refer to the 

LED Indicators

 section for more 

information.

Typical PCI-PCI bridges are used to add PCI devices to a PCI hierarchy in which all the bridges 
and devices are contained within a single chassis. Because of this, BIOSes and operating systems 
make the assumption that all PCI devices in the entire hierarchy will be available as soon as code 
execution begins at power-up time. This assumption means that all of the expansion chassis must 
be turned on before the host PC for the BIOS and OS to correctly configure a MXI-Express 
system.

Note

In some cases where there is an invalid MXI-Express x1 connection, some 

boards may report a valid link while others do not. It is important to observe a valid 
link status across 

all

 connected MXI-Express x1 boards when the host is powered on 

to ensure a valid configuration.

Powering Off the MXI-Express x1 System

Because operating systems and drivers commonly make the assumption that PCI devices will be 
present in the system from power-up to power-down, it is important not to power off the 
expansion chassis until after the host PC is powered off. Powering off the expansion chassis 
while the host is still on can cause crashes or hangs. However, once the host PC is powered off, 
the order that the expansion chassis are powered off is not important.

LED Indicators

The LEDs on MXI-Express x1 cards provide status information about power supplies and link 
state. The PCI-8361, PXI-8364/8367, and PXIe-8364 all have one tri-color LED on the panel, 
indicating power and link status. The PCIe-8362 has two tri-color LEDs on the panel, indicating 
power and link status for each port. The PXI-8360/8368 and PXIe-8360 have two LEDs, one for 
power supply status and one for link state.

Note

In some cases where there is an invalid MXI-Express x1 connection, some 

boards may report a valid link while others do not. It is important to observe a valid 
link status across 

all

 connected MXI-Express x1 boards when the host is powered on 

to ensure a valid configuration.

Summary of Contents for PCI-8361

































































































































Reviews: