background image

1-12

|

ni.com

Chapter 1

Introduction

Table 1-2 provides information on which host boards can be connected to the corresponding 
targets. 

Larger MXI-Express x1 Systems

By leveraging the PCI Express technology used in MXI-Express x1 products, you can connect 
more than a single chassis to a host controller.

The PCIe-8362, for example, has two MXI-Express x1 ports. This allows for connecting 
two targets simultaneously, also known as a star configuration or star topology. Also, if multiple 
PCI or PCI Express slots are available in the host PC, additional PXI or PXI Express chassis can 
be connected by installing additional NI MXI-Express x1 host boards to achieve the same star 
topology.

Table 1-2.  

MXI-Express x1 Connectivity Support From a Host PC or Laptop

From Host

Targets

PXI Chassis

VXI 

Chassis

PXI Express 

Chassis

MXI-Express 

RIO

Slot Type

Product

PXI-

8360

PXI-

8368

PXI-

1033

*

VXI-

8360T

PXIe-

8360

PXIe-
1073

*

NI 

9157

*

NI 

9159

*

PCI

PCI-8361

PCI-8366

PCI 
Express x1

PCIe-8361

PCI 
Express x1

PCIe-8362

PCI 
Express x1

PCIe-8363

ExpressCard

ExpressCard-
8360

Industrial 
Controller

NI 3100/3110

*

*

 Product has an integrated MXI-Express x1 port. 

† 

These configurations are not supported, even though the front panel MXI connectors are mechanically compatible. 

For these configurations the boards will likely report a valid cable link via the front panels LEDs. Since these link 
scenarios expose a possible data integrity issue that may not be obvious to the user, National Instruments strongly 
recommends against using these configurations.

Note

: For installation instructions and other information concerning the PXI-1033, PXIe-1073, VXI-8360T, NI 9157, 

NI 9159, and the NI 3100/3110, refer to their respective user manuals.

Note

: PCI Express host slots will give better throughput and latency performance than PCI slots.

Summary of Contents for PCI-8361

































































































































Reviews: