background image

©

 National Instruments Corporation

5

Getting Started with the NI EVS-1464RT

Mount the NI EVS-1464RT with the heatsink facing upward. If you mount the NI EVS-1464RT on 
a wall or other vertical surface, mount the device so that the heat sink fins are vertical.

Refer to the 

NI EVS-1464 Series User Manual

 for dimensional drawings, additional mounting 

information, and detailed device specifications.

Unpack and Verify Components

Remove the NI EVS-1464RT from the package and inspect the system for any sign of damage. Notify 
National Instruments if the system appears damaged in any way. Do not use a damaged system.

Hardware Installation

Ensure that the AC input to the external power supply is disconnected before plugging in or unplugging 
any connector. Ground the unit to minimize the possibility of static electricity damage.

Refer to Figure 1 while completing the following steps to install the NI EVS-1464RT.

Figure 1.  

NI EVS-1464RT Connectors

1

Primary Network Connector

2

Secondary Network Connector

3

Reset Switch

4

Audio In Connector

5

Audio Out Connector

6

Safe Mode/IP Reset/No App/
User 1/CF Master/Slave Switches

7

User 2/User 1/HDD/Power LEDs

8

CompactFlash Slot

9

Power Supply Connector

10 Grounding Lug
11 DVI-I Connector
12 IEEE 1394b Bilingual Connector
13 ISO/CAM Power Status LEDs

14 IEEE 1394b Bilingual Connector
15 RS-232 Serial Connector (COM1) 
16 MXI Express x1 Connector
17 Digital I/O Connector
18 USB Connectors

RESET

MXIex1

COMPACT FLASH

INPUT

10-20V

90W  MAX

USER 2
USER 1
HDD
POWER

CF MS/SL

SAFE MODE

IP

 RESET

NO APP

USER 1

DIGITAL I/O

!

IEEE 1

3

94

b

IEEE 1

3

94

b

CAM

I

S

O

1

2

3

7

8

9

11

16

1

8

6

5

17

14 1

3

12

15

10

4

Summary of Contents for NI EVS-1464RT




















Reviews: