background image

FP-AI-102 and cFP-AI-102

8

ni.com

backplane PE ground terminal to the system safety ground 
using 14 AWG (1.6 mm) wire with a ring lug. Use the 5/16 in. 
panhead screw shipped with the backplane to secure the ring 
lug to the backplane PE ground terminal.

As with any hazardous voltage wiring, make sure that all 
wiring and connections meet applicable electrical codes and 
commonsense practices. Mount terminal bases and backplanes 
in an area, position, or cabinet that prevents accidental or 
unauthorized access to wiring that carries hazardous voltages.

The isolation of the [c]FP-AI-102 is certified as 
double-insulated for working voltages of 250 V

rms

. Do 

not

 use 

the [c]FP-AI-102 as the only isolating barrier between human 
contact and working voltages of more than 250 V

rms

.

Operate the [c]FP-AI-102 only at or below Pollution Degree 2. 
Pollution Degree 2 means that only nonconductive pollution 
occurs in most cases. Occasionally, however, a temporary 
conductivity caused by condensation must be expected.

Do 

not

 operate FieldPoint products in an explosive atmosphere 

or where there may be flammable gases or fumes. If you need 
to operate FieldPoint products in such an environment, the 
FieldPoint products 

must

 be in a suitably rated enclosure.

Operate the [c]FP-AI-102 at or below Installation Category II. 
Installation Category II is for measurements performed on 
circuits directly connected to the electrical distribution system. 
This category refers to local-level distribution, such as that 
provided by a standard wall outlet.

Specifications

The following specifications are typical for the range –40 to 70 °C 
unless otherwise noted. Gain error is calculated as a percentage of 
input.

Input Characteristics

Number of channels.......................... 8

ADC resolution................................. 12 bits

Type of ADC..................................... Successive approximation

Update rate (all channels) ................. 360 Hz (2.8 ms)

Summary of Contents for FP-AI-102














Reviews: