National Instruments CMS-9068 Maintaining Hardware Download Page 12 | Manualshive

Page: 12 / 23

background image

NI cRIO-9068

1. Use the Phillips #1 screwdriver to remove the two screws from the back of the

cRIO-9068.

2. Use the screwdriver and the M3 × 20 screws to attach the adapter bracket to the

cRIO-9068. NI provides these screws with the desktop mounting kit.

Note

You must use the screws provided with the NI desktop mounting kit

because they are the correct depth and thread for the cRIO-9068.

3. Align the brackets with the mounting holes on the ends of the cRIO-9068.
4. Use the Phillips #2 screwdriver to tighten the captive screws on the end of the brackets.

Desktop Mounting Dimensions

The following figures show the desktop mounting dimensions for the cRIO-9068.

Maintaining NI CMS-9068, MMS-9068, and EMSA-9068 Hardware for an NI InsightCM Device

|

© National Instruments

|

11

«
...
10
11
12
13
14
...
»

Summary of Contents for CMS-9068
























Reviews:

No comments

Related manuals for CMS-9068

Brand: NEC Pages: 304

Brand: Aalborg Pages: 15

Brand: Aalborg Pages: 48

Brand: janitza Pages: 58

Brand: Magellan Pages: 44

Brand: Namron Pages: 3

Brand: D+H Pages: 32

FEBCO 860 Small Series

Brand: Watts Pages: 12

Brand: Bardiani Valvole Pages: 54

Brand: Parker Pages: 478

Brand: KIPI Pages: 44

Brand: Gallagher Pages: 2

Brand: SMC Networks Pages: 10

Brand: Harman Pages: 20

Brand: Water Specialist Pages: 60

Brand: aerl Pages: 27

Brand: KAR-TECH Pages: 55

10 AMP RVC-MPPT

Brand: Go Power Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands