CARE AND MAINTENANCE FOR
AUSCULTATION FEATURE
1.
Prior to storing equipment, ensure the batteries
in the remote control and SmartScope
™
are
removed.
2.
Adhesive remaining on the manikin from use
of the blue and green location stickers can be
removed using Nasco cleaner. Apply Nasco
Cleaner to a clean, soft, dry cloth and wipe
residual adhesive. Be cautious not to over-
wipe painted areas.
3.
Newsprint, ballpoint pen, and printed plastics
will leave an indelible mark.
4.
Alcohol prep pads are included to sterilize
SmartScope
™
earpieces between users.
AVAILABLE SUPPLIES
LF01144U
Additional SmartScope
™
LF01148U
Replacement Remote Control
LF01170U
Adult Tracheostomy Tube
LF01189U
110V 30-watt Amplifier/Speaker with
speaker cord
LF01189EXU
220V 30-watt Amplifier/Speaker with
speaker cord
LF03480U
Alcohol Pads (Pkg. of 100)
LF09919U
Nasco Cleaner
SB10828U
“AA” Batteries, 2 pack
SB27438U
“AAA” Batteries, 4 pack
GENERAL INSTRUCTION FOR CARE OF YOUR BASIC, COMPLETE, ADVANCED, AUSCULTATION,
AND ADVANCED AUSCULTATION
GERI™/KERI™
MANIKIN
1.
Most cleaning can be done with a soft cloth, mild soap, and warm water. Avoid over-
washing the painted areas on the manikin.
2.
Stubborn stains can be treated by using Nasco Cleaner and a soft cloth.
3.
Stains caused by make-up, ink, and newsprint are indelible and cannot be removed. Avoid contact with
these substances and do not apply cosmetics or Betadine
®
solution to the manikin.
4.
Follow cleaning, care, storage, and maintenance guidelines in each section of this manual.
5.
It is recommended that batteries are removed from the Electronic Control Unit (equipped with the
Blood Pressure Simulator), remote control, and SmartScope
™
(equipped with the Auscultation feature)
prior to storing your equipment for future use.
21
Listening to Selected Heart and Lung Sounds
1.
Follow the instructions above to activate
remote control, SmartScope
™
, and select
desired sounds.
2.
Place the earpieces of the SmartScope
™
in ears
angled in a forward position.
3.
Place the diaphragm of the SmartScope
™
over
the appropriate sites on the manikin.
4.
Use included laminated key cards for location
instruction.
5.
For additional location instruction, use the
green color-coded stickers for lung sites found
and the blue color-coded stickers for the heart
sites found.
6.
Correct placement of the SmartScope
™
is
required to hear the sounds. Moving the
SmartScope
™
slowly across the area will help
locate the sensor in the torso so that the
sounds can be heard.
Note:
The SmartScope
™
is only for use with the
Auscultation feature. It is not a standard stethoscope.
Using the Amplified Speaker (purchased sepa-
rately LF01189U)
1.
Locate the SmartScope
™
and speaker cord
included with the 30-watt amplifier/speaker.
2.
Plug the speaker cord into the speaker jack on
top of the SmartScope™ box.
3.
Plug the amplifier/speaker into the 110V power
source.
4.
When the speaker is connected, the
SmartScope
™
earpieces will not work; sounds
will only be amplified through the speaker.
5.
Select the desired heart and lung sounds fol-
lowing the instructions above.
6.
Place the diaphragm of the SmartScope
™
over
the appropriate sites on the manikin.
Note:
The remote has a battery saver mode that
shuts the unit down after eight minutes if the remote
is left on the same setting. To prevent this shutdown,
select a different heart or lung sound within the
eight-minute time period.
HC18000028INM23.indd 21
11/16/18 9:25 AM
