background image

1

W415-0619 / B / 03.03.08

INSTALLATION 

AND

OPERATION INSTRUCTIONS

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada 

 (705)721-1212 

 fax(705)722-6031

www.napoleonfireplaces.com 

 [email protected]

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.22, ANSI Z21.50 FOR VENTED GAS FIREPLACE.

GT8N

NATURAL GAS

GT8P

PROPANE

- Do not store or use gasoline or other flammable 
vapors and liquids in the vicinity of this or any other 
appliance.
- WHAT TO DO IF YOU SMELL GAS:
 

 Do not try to light any appliance.

 

 Do not touch any electrical switch; do not use

 

   any phone in your building.

 

 Immediately call your gas supplier from a 

 

   neighbour’s phone. Follow the gas supplier’s

 

   instructions. 

 

 If you cannot reach your gas supplier, call the 

 

   fire department.

- Installation and service must be performed by a 
qualified installer, service agency or the supplier. 

SAFETY INFORMATION

Certified for Canadian and United States using ANSI/CSA Methods.

If the information in these instructions are not 
followed exactly, a fire or explosion may result 
causing property damage, personal injury or loss 
of life.

!

WARNING

INSTALLER:  LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER:  RETAIN THIS MANUAL FOR FUTURE REFERENCE.

$10.00

Summary of Contents for TORCH GT8P























Reviews: