background image

4

PRECAUTIONS

Do not use the heater in an explosive atmosphere.
Keep the heater away from areas where gasoline or other
flammable liquids or vapors are stored.

Prior to use, check for damaged parts such as hoses,
regulators, pilot or burner.

Always assure there is ample fresh air ventilation. 
For outdoor use ONLY.

Never replace or substitute the regulator with any regulator
other than the factory suggested replacement.

Do not clean 

 with cleaners that are combustible

or corrosive.

the heater

Do not paint radiant screen, control panel or top canopy
reflector.

All leak tests should be done with a soapy solution. NEVER
USE AN OPEN FLAME TO CHECK FOR LEAKS.

The LP gas cylinder should be turned off when the 
 heater is not in use.

At least once a year

the unit should be inspected

 for the

presence of spiders, spider webs or other insects. Check the
 heater immediately if any of the following exist:

1. The smell of gas in conjunction with extreme yellow

colored tips of the burner flames.

2. The heater does not reach temperature.

3. The burner makes popping noise during use (a slight

popping noise is normal when the burner is extinguished
after using).

The propane hose with regulator assembly shall be located
out of pathways where people may trip over it or in areas
where the hose will not be subject to accidental damage.

Children and adults should be aware of the hazards of high
surface temperature.

Young children should be carefully supervised when they
are in the area of the heater.

Clothing or other flammable material should not be hung
from the heater, or placed on or near the heater.

Installation and repair should be done by a qualified
service person. The heater should be inspected before
use and cleaning may be required at least once a year, or as
necessary. It is imperative that control compartment, burner
and circulating air passageways of the heater be kept
clean.

Keep the appliance area clear of combustible materials
such as gasoline and other flammable vapors and liquids.

Do not obstruct the flow of combustion and ventilation air.

Keep the ventilation opening of the cylinder enclosure free
and clear of debris.

NOTE: PLEASE READ THE FOLLOWING SAFETY  RULES

The appliance shall not be used in basements or below
ground level.
It must always be placed on a solid and level surface.

Read the instructions before use. 

This appliance must be installed in 

accordance with such regulations as 

are in force.

This appliance must only be used outdoors.

Using this product in an enclosed area may cause

injury, death or property damage. 

WARNING

Disconnect LPG bottle before moving the heater.

Any guard or other protective device removed for 
servicing the heater must be replaced prior to 
operating the heater.

Do not attempt to alter unit in any manner.
EXAMPLE: using the heater without the top canopy 
reflector or radiant screen. 
Do not shorten the burner post assembly.

Summary of Contents for PTHC38PK















Reviews: