W415-1427 / A / 09.27.17
40
EN
A.
Turn off the electrical power and the gas supply to the appliance.
B.
Open the lower louvre control door, the two side doors and the fire viewing door. Remove the logs.
C.
Remove the relief door assembly held on with 6 screws. Discard the gasket.
D.
Disconnect the two blower wires. Remove the blower bracket held on with 4 screws.
E.
Replace the blower using the existing bracket. When connecting the replacement blower, tighten
the screws without distorting the rubber grommets. Replace the bracket / blower assembly in the
appliance.
F.
Reconnect the two wires. Hold the replacement gasket in place and reattach the relief door assembly.
Replace the logs. Close all doors.
G.
Turn the gas supply and electricity back on.
Because the blower is thermally activated, when turned on, it will automatically start approximately 15-30
minutes after lighting the appliance and will run for approximately 30-45 minutes after the appliance has been
turned off. Use of the fan increases the output of heat.
Drywall dust will penetrate into the blower bearings causing irreparable damage and must be prevented from
coming into contact with the blower or its compartment. Any damage resulting from this condition is not
covered by the warranty policy.
8.3 CARE OF GLASS
8.4 CARE OF PLATED PARTS
W415-1427 / 12.23.14
39
EN
5.1
DO NOT CLEAN GLASS WHEN HOT! DO NOT USE
ABRASIVE CLEANERS TO CLEAN GLASS.
Buff lightly with a clean dry soft cloth. Clean both sides
of the glass after the
rst 10 hours of operation with a
recommended
replace glass cleaner. Thereafter clean
as required. If the glass is not kept clean permanent
discoloration and / or blemishes may result.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
!
WARNING
6.1
If the appliance is equipped with plated parts, you must clean
ngerprints or other marks from the plated
surfaces before operating the appliance for the
rst time. Use a glass cleaner or vinegar and towel to clean.
If not cleaned properly before operating for the
rst time, the marks can cause permanent blemishes on
the plating. After the plating is cured, the
ngerprints and oils will not affect the
nish and little maintenance
is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause
discolouration on plated parts.
NOTE: The protective wrap on plated parts is best removed when the assembly is at room
temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat
source.
8.2 REPLACEMENT BLOWER INSTALLATION
RELIEF DOOR GASKET
RELIEF DOOR
TWIN BLOWER
P
I
P ILOT
N
O
L
O
T
H I
L O
FF
O
BLOWER
THERMODISC
black
ground
VARIABLE
SPEED
SWITCH
white
A.
Turn off the electrical power and the gas supply to the appliance.
B.
Open the lower louvre control door, the two side doors and the
re viewing door. Remove the logs.
C.
Remove the relief door assembly held on with 6 screws. Discard the gasket.
D.
Disconnect the two blower wires. Remove the blower bracket held on with 4 screws.
E.
Replace the blower using the existing bracket. When connecting the replacement blower, tighten
the screws without distorting the rubber grommets. Replace the bracket / blower assembly in the
appliance.
F.
Reconnect the two wires. Hold the replacement gasket in place and reattach the relief door assembly.
Replace the logs. Close all doors.
G.
Turn the gas supply and electricity back on.
Because the blower is thermally activated, when turned on, it will automatically start approximately 15-30
minutes after lighting the appliance and will run for approximately 30-45 minutes after the appliance has been
turned off. Use of the fan increases the output of heat.
Drywall dust will penetrate into the blower bearings causing irreparable damage and must be prevented
from coming into contact with the blower or its compartment. Any damage resulting from this condition is not
covered by the warranty policy.
8.3 CARE OF GLASS
8.4 CARE OF PLATED PARTS
5.5.1
This appliance is factory equipped with 5mm ceramic glass. Use only replacement glass available from your
Napoleon® dealer. DO NOT SUBSTITUTE MATERIALS.
8.2 REPLACEMENT BLOWER INSTALLATION
W415-1427 / 12.23.14
39
EN
5.1
DO NOT CLEAN GLASS WHEN HOT! DO NOT USE
ABRASIVE CLEANERS TO CLEAN GLASS.
Buff lightly with a clean dry soft cloth. Clean both sides
of the glass after the
rst 10 hours of operation with a
recommended
replace glass cleaner. Thereafter clean
as required. If the glass is not kept clean permanent
discoloration and / or blemishes may result.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
!
WARNING
6.1
If the appliance is equipped with plated parts, you must clean
ngerprints or other marks from the plated
surfaces before operating the appliance for the
rst time. Use a glass cleaner or vinegar and towel to clean.
If not cleaned properly before operating for the
rst time, the marks can cause permanent blemishes on
the plating. After the plating is cured, the
ngerprints and oils will not affect the
nish and little maintenance
is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause
discolouration on plated parts.
NOTE: The protective wrap on plated parts is best removed when the assembly is at room
temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat
source.
8.2 REPLACEMENT BLOWER INSTALLATION
RELIEF DOOR GASKET
RELIEF DOOR
TWIN BLOWER
P
I
P ILOT
N
O
L
O
T
H I
L O
FF
O
BLOWER
THERMODISC
black
ground
VARIABLE
SPEED
SWITCH
white
A.
Turn off the electrical power and the gas supply to the appliance.
B.
Open the lower louvre control door, the two side doors and the
re viewing door. Remove the logs.
C.
Remove the relief door assembly held on with 6 screws. Discard the gasket.
D.
Disconnect the two blower wires. Remove the blower bracket held on with 4 screws.
E.
Replace the blower using the existing bracket. When connecting the replacement blower, tighten
the screws without distorting the rubber grommets. Replace the bracket / blower assembly in the
appliance.
F.
Reconnect the two wires. Hold the replacement gasket in place and reattach the relief door assembly.
Replace the logs. Close all doors.
G.
Turn the gas supply and electricity back on.
Because the blower is thermally activated, when turned on, it will automatically start approximately 15-30
minutes after lighting the appliance and will run for approximately 30-45 minutes after the appliance has been
turned off. Use of the fan increases the output of heat.
Drywall dust will penetrate into the blower bearings causing irreparable damage and must be prevented
from coming into contact with the blower or its compartment. Any damage resulting from this condition is not
covered by the warranty policy.
8.3 CARE OF GLASS
8.4 CARE OF PLATED PARTS
5.5.1
This appliance is factory equipped with 5mm ceramic glass. Use only replacement glass available from your
Napoleon® dealer. DO NOT SUBSTITUTE MATERIALS.
W415-1427 / 12.23.14
39
EN
5.1
DO NOT CLEAN GLASS WHEN HOT! DO NOT USE
ABRASIVE CLEANERS TO CLEAN GLASS.
Buff lightly with a clean dry soft cloth. Clean both sides
of the glass after the
rst 10 hours of operation with a
recommended
replace glass cleaner. Thereafter clean
as required. If the glass is not kept clean permanent
discoloration and / or blemishes may result.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
!
WARNING
6.1
If the appliance is equipped with plated parts, you must clean
ngerprints or other marks from the plated
surfaces before operating the appliance for the
rst time. Use a glass cleaner or vinegar and towel to clean.
If not cleaned properly before operating for the
rst time, the marks can cause permanent blemishes on
the plating. After the plating is cured, the
ngerprints and oils will not affect the
nish and little maintenance
is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause
discolouration on plated parts.
NOTE: The protective wrap on plated parts is best removed when the assembly is at room
temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat
source.
8.2 REPLACEMENT BLOWER INSTALLATION
RELIEF DOOR GASKET
RELIEF DOOR
TWIN BLOWER
P
I
P ILOT
N
O
L
O
T
H I
L O
FF
O
BLOWER
THERMODISC
black
ground
VARIABLE
SPEED
SWITCH
white
A.
Turn off the electrical power and the gas supply to the appliance.
B.
Open the lower louvre control door, the two side doors and the
re viewing door. Remove the logs.
C.
Remove the relief door assembly held on with 6 screws. Discard the gasket.
D.
Disconnect the two blower wires. Remove the blower bracket held on with 4 screws.
E.
Replace the blower using the existing bracket. When connecting the replacement blower, tighten
the screws without distorting the rubber grommets. Replace the bracket / blower assembly in the
appliance.
F.
Reconnect the two wires. Hold the replacement gasket in place and reattach the relief door assembly.
Replace the logs. Close all doors.
G.
Turn the gas supply and electricity back on.
Because the blower is thermally activated, when turned on, it will automatically start approximately 15-30
minutes after lighting the appliance and will run for approximately 30-45 minutes after the appliance has been
turned off. Use of the fan increases the output of heat.
Drywall dust will penetrate into the blower bearings causing irreparable damage and must be prevented
from coming into contact with the blower or its compartment. Any damage resulting from this condition is not
covered by the warranty policy.
8.3 CARE OF GLASS
8.4 CARE OF PLATED PARTS
5.5.1
This appliance is factory equipped with 5mm ceramic glass. Use only replacement glass available from your
Napoleon® dealer. DO NOT SUBSTITUTE MATERIALS.
W415-1427 / 12.23.14
39
EN
5.1
DO NOT CLEAN GLASS WHEN HOT! DO NOT USE
ABRASIVE CLEANERS TO CLEAN GLASS.
Buff lightly with a clean dry soft cloth. Clean both sides
of the glass after the
rst 10 hours of operation with a
recommended
replace glass cleaner. Thereafter clean
as required. If the glass is not kept clean permanent
discoloration and / or blemishes may result.
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
!
WARNING
6.1
If the appliance is equipped with plated parts, you must clean
ngerprints or other marks from the plated
surfaces before operating the appliance for the
rst time. Use a glass cleaner or vinegar and towel to clean.
If not cleaned properly before operating for the
rst time, the marks can cause permanent blemishes on
the plating. After the plating is cured, the
ngerprints and oils will not affect the
nish and little maintenance
is required, just wipe clean as needed. Prolonged high temperature burning with the door ajar may cause
discolouration on plated parts.
NOTE: The protective wrap on plated parts is best removed when the assembly is at room
temperature but this can be improved if the assembly is warmed, using a hair dryer or similar heat
source.
8.2 REPLACEMENT BLOWER INSTALLATION
RELIEF DOOR GASKET
RELIEF DOOR
TWIN BLOWER
P
I
P ILOT
N
O
L
O
T
H I
L O
FF
O
BLOWER
THERMODISC
black
ground
VARIABLE
SPEED
SWITCH
white
A.
Turn off the electrical power and the gas supply to the appliance.
B.
Open the lower louvre control door, the two side doors and the
re viewing door. Remove the logs.
C.
Remove the relief door assembly held on with 6 screws. Discard the gasket.
D.
Disconnect the two blower wires. Remove the blower bracket held on with 4 screws.
E.
Replace the blower using the existing bracket. When connecting the replacement blower, tighten
the screws without distorting the rubber grommets. Replace the bracket / blower assembly in the
appliance.
F.
Reconnect the two wires. Hold the replacement gasket in place and reattach the relief door assembly.
Replace the logs. Close all doors.
G.
Turn the gas supply and electricity back on.
Because the blower is thermally activated, when turned on, it will automatically start approximately 15-30
minutes after lighting the appliance and will run for approximately 30-45 minutes after the appliance has been
turned off. Use of the fan increases the output of heat.
Drywall dust will penetrate into the blower bearings causing irreparable damage and must be prevented
from coming into contact with the blower or its compartment. Any damage resulting from this condition is not
covered by the warranty policy.
8.3 CARE OF GLASS
8.4 CARE OF PLATED PARTS
5.5.1
This appliance is factory equipped with 5mm ceramic glass. Use only replacement glass available from your
Napoleon® dealer. DO NOT SUBSTITUTE MATERIALS.
