W415-1427 / A / 09.27.17
27
EN
4.3.3 ADDING VENT SECTIONS
Add chimney sections, according to the manufacturers installation instructions. The chimney must extend at
least, 3 feet (1m) above its point of contact with the roof and at least 24 inches (61cm) higher than any wall,
roof, building or obstacle within 10 feet (3m) horizontally.
59.1B
3 FT
(1m)
MIN
3 FT (1m)
MIN
10 FT (3m)
OR MORE
FLAT ROOF
WALL
10 FT (3m)
TO NEAREST
ROOFLINE
RIDGE
LESS THAN
10 FEET
(3m)
24” (61cm) MIN
3 FT (1m)
MIN
24” (61cm)
MIN
LESS THAN
10 FEET
(3m)
3 FT (1m)
MIN
24” (61cm)
MIN
REV B : Added metric dimensions
4.3.4 INSTALLING NATURAL VENT
ADAPTER INSTALLATION:
•
Remove the spill switch bracket from the rear of the
adapter.
•
Gently pull the two wire terminals (located inside the
7" (178mm) flue collar at the top of the appliance) out
approximately 8" (203mm).
•
Bring the wires through the lower hole in the adapter
and out the spill switch opening. To pass the wires
through the hole more easily, temporarily take the two
terminals together.
•
With the spill switch opening aligned to the back of the
appliance, take hold of the adaptor base and push the
crimped edge into the appliance flue collar.
•
Connect the wire terminals to the spill switch and
resecure the bracket.
For aesthetics, the adaptor has been designed to accept
a standard matte black 7" (178mm) appliance pipe and a
decorative black band (standard with the GS150KT). Both are
available from your local authorized dealer / distributor.
W415-1427 / 12.23.14
26
EN
4.3.3 ADDING VENT SECTIONS
Add chimney sections, according to the manufacturers installation instructions. The chimney must extend at
least, 3 feet (1m) above its point of contact with the roof and at least 2 feet (0.6m) higher than any wall, roof,
building or obstacle within 10 feet (3m) horizontally.
59.1B
3 FT
(1m)
MIN
3 FT (1m)
MIN
10 FT (3m)
OR MORE
FLAT ROOF
WALL
10 FT (3m)
TO NEAREST
ROOFLINE
RIDGE
LESS THAN
10 FEET
(3m)
2 FT (0.6m) MIN
3 FT (1m)
MIN
2 FT (0.6m)
MIN
LESS THAN
10 FEET
(3m)
3 FT (1m)
MIN
2 FT (0.6m)
MIN
4.3.4 INSTALLING NATURAL VENT
ADAPTER INSTALLATION:
•
Remove the spill switch bracket from the rear of the
adapter.
•
Gently pull the two wire terminals (located inside the
7" (178mm)
ue collar at the top of the appliance) out
approximately 8" (203mm).
•
Bring the wires through the lower hole in the adapter and
out the spill switch opening. To pass the wires through
the hole more easily, temporarily take the two terminals
together.
•
With the spill switch opening aligned to the back of the
appliance, take hold of the adaptor base and push the
crimped edge into the appliance
ue collar.
•
Connect the wire terminals to the spill switch and re secure
the bracket.
For aesthetics, the adaptor has been designed to accept a standard
matte black 7" (178mm) appliance pipe and a decorative black
band (standard with the GS150KT). Both are available from your
local authorized dealer / distributor.
SWITCH
SPILL
ADAPTER
