Napoleon BIPRO665RBPSS-3, Manual

Page: 4 / 64

4
EN
www.napoleon.com N415-0542 OCT 02.19
General Information
This Gas Barbecue Is Certified under Canadian and American National Standards CSA 1.6-2018 and ANSI
Z21.58-2018 respectively for Outdoor Gas Grills and should be installed to conform with local codes. In
absence of local codes, install to the current CAN B149.1 Natural Gas and Propane Installation Code in
Canada or to the National Fuel Gas Code, ANSI Z223.1 in the United States.
If a rotisserie motor is used, it must be electrically grounded in accordance with local codes or, in absence
of local codes, with the current CSA C22.1 Canadian Electrical Code in Canada or the National Electrical
Code, ANSI/NFPA 70 in the United States.
WARNING: This product can expose you to chemicals including lead and lead compounds, which are
known to the State of California to cause cancer, and chemicals including di-n-butyl phthalate, which are
known to the State of California to cause birth defects or other reproductive harm. For more information
go to www.P65Warnings.ca.gov.
Propane Cylinder Specifications
WARNING!
If these instructions are not followed exactly, a fire causing death or serious injury
may occur.
WARNING!
Do not store a spare propane cylinder on the shelf beneath the barbecue.
If the gas grill is being supplied with propane from a portable cylinder, a regulator specified by the manu -
facturer must be used. The regulator must supply a pressure of 11 inches water column (0.39 PSI) to the
gas grill and have a QCC1 type fitting. Cylinders to be used with this unit must be supplied with a QCC1
cylinder valve. A QCC1 cylinder has a positive seating connection, which will not allow gas flow until a
positive seal has been achieved. It is also equipped with an excess flow device. In order to attain full flow
to the grill, the valves must be in the off position when the cylinder valve is turned on.
A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a
cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in accordance
with the specifications for LP-gas cylinders of the National Standard of Canada, CAN/CSA-b339, Cylinders,
Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable or the Speci -
fications for LP-Gas Cylinders of the U.S. Department of Transportation (D.O.T.). Cart models have been
designed for use with a 20 lb (9.1 kg) size propane cylinder only (not supplied).
The propane cylinder must be provided with a cylinder connection device compatible with the connection
for outdoor cooking appliances. The propane cylinder must be provided with a shut-off valve terminat -
ing in a propane cylinder valve type QCC1, and a safety relief device having direct communication with
the vapor space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and
the cylinder shall include a collar to protect the cylinder valve. The cylinder shall incorporate a listed OPD
(overfill protection device). Do not store a spare LP-gas cylinder under or near this appliance. Never fill the
cylinder beyond 80 percent full. If the preceding information is not followed exactly, a fire causing death or
serious injury may occur.
Gas Hook-Up Instructions
WARNING!
This grill is designed for non-combustible enclosures only, and must be installed and
serviced by a qualified installer to local codes.
WARNING!
Cabinet frame, cabinet, and counter top must be made from non-combustible
material.
WARNING!
As indicated on the rating plate, this gas grill is designed to operate with gas supply
pressures of 11” WC for Propane and 7” WC for Natural Gas. For installations where the gas supply
pressure exceeds these requirements, a regulator must be installed upstream of the grill’s components.
If the gas supply pressure is lower than these requirements, the unit will be under-fired and will not
reach the maximum temperatures. Ensure that the supply line size complies with local and/or national
installation codes.
BUILT IN PROPANE GAS HOOK-UP : The piping up to the gas grill is the responsibility of the installer and
piping should be located as shown in the built-in instructions. A flexible metal connector is included to
simplify the installation of the unit. Connect this flexible metal connector to the flare fitting on the end of
the manifold. Connect the other end of the connector to the gas piping. Ensure that the connector does
!
!
!