background image

14 

StarLink

 SLE Commercial LTEVI & LTEAI Series Dual-Path Alarm Communicators -- Installation Instructions 

WIRING THE TAMPER SWITCHES  

Before installation and wiring, the tamper switches (part 

GEM-

Tamperkit

)  are  normally  open  devices;  when  placed  into 

the circuit and into operation, they are normally closed devic-

es.   

 

Tamper switches protect against the opening of the radio cabi-

net door or the removal of the radio enclosure from the wall or 

other mounting surface.   

 

There are two places in the cabinet to mount tamper switches: 

(1)  To  prevent  cabinet  removal  from  the  wall,  located  on  the 

left  side  of  the  cabinet  there  is  one  knockout  for  the  switch 

plunger and three mounting holes (in the enclosure sheet met-

al).  (2) To protect the cabinet door,  mount a tamper switch in 

the  three  mounting  holes  (in  the  enclosure  sheet  metal).  

When mounted, the switch button  contacts the inside surface 

of the door.  

Note:   

Be sure to alert the user that opening the 

enclosure door will cause a tamper alarm.   

 

Wiring a normally closed sensor loop for tamper supervision, 

wire to a zone on the control panel. 

GEM-Tamperkit 

consists of 

Description 

QTY 

SC206LF 

Slotted Pan Head 6-32 x 3/4 

Machine Screw 

SW105 

Tamper Switch 

Tamper Switch Mounting Instructions 

B

a

ck 

T

am

pe

Doo

r Tampe

VIEW OF TAMPER SWITCHES: 

(1) = ENCLOSURE BASE;  

(2-BACK) = TAMPER SWITCH TO PREVENT REMOVAL FROM WALL;  

(3-DOOR) = TAMPER SWITCH TO PROTECT THE ENCLOSURE 

DOOR 

Name 

Format Type 

Handshake Frequency 

Speed 

Ademco Slow 

4/2 

1400 Hz or 2300Hz 

10pps 

Ademco Slow 

4/2 checksum 

1400 Hz or 2300Hz 

10pps 

Radionics Slow 

4/2 

2300Hz 

10pps 

Radionics Slow 

4/2 checksum 

2300Hz 

10pps 

Silent Knight Fast 

4/2 

1400 Hz or 2300Hz 

20pps 

Silent Knight Fast 

4/2 checksum 

1400 Hz or 2300Hz 

20pps 

Radionics Fast 

4/2 

2300Hz 

40pps 

Radionics Fast 

4/2 checksum 

2300Hz 

40pps 

Universal High Speed 

4/2 

1400 Hz or 2300Hz 

40pps 

Universal High Speed 

4/2 checksum 

1400 Hz or 2300Hz 

40pps 

4/2

 Pulse 

Diali

ng 

Forma

 

Compa

tibili

ty

 

Note:

  

Th

e SL

E Du

al

-Pa

th Seri

es R

ad

ios 

are

 comp

atib

le

 w

ith 

any

 Liste

d 4

/2 

Re

cei

ver su

ch 

as the

 Ade

mc

o

 68

5.

 

Summary of Contents for SLE-LTEAI-CFB

















Reviews: