background image

StarLink

 SLE Commercial LTEVI & LTEAI Series Dual-Path Alarm Communicators -- Installation Instructions 

3.  When  used  DACT  for  Central  Station  communication,  two 

means of communication are required.  The primary chan-

nel shall be telephone line.  Cellular or internet communica-

tion shall be limited for the secondary means of communi-

cation and comply with 26.6.3 NFPA 72, 2010 edition.  An-

other telephone line also may be used as secondary mean 

of communication. 

4.  The  above-referenced  equipment  shall  be  used  only  with 

listed fire alarm control panels and devices, with which the 

compatibility has been determined by UL Listing Report  

5.  Only enclosures painted red in color shall be used. 

6.  Underwriters  Laboratories  Inc.'s  listing  requirements  and 

limitations shall be complied with. 

to the transmitted message 

e.  The  maximum  duration  between  the  initiation  of  an 

alarm signal at the protected  premises, transmission of 

the signal, and subsequent display and recording of the 

alarm signal at  the  Central  Station  shall  not  exceed 90 

seconds 

f.  A  spare  Central  Station  Receiver  shall  be  provided  at 

the Central Station and shall be able to be switched into 

the place of a failed unit within 30 seconds after detec-

tion of failure 

g.  All applicable requirements of Federal Communications 

Commission (FCC) shall be complied with. 

Summary of Contents for SLE-LTEAI-CFB

















Reviews: