background image

Page 13

6.2 SERVICE ‘C’ INSTRUCTIONS - Outlet valves

(Every 4 years or 24,000 hours)

REPLACING OUTLET NON-RETURN VALVES

OUTLET NON 

RETURN VALVES

OUTLET MANIFOLD

Figure C.2

M10 SOCKET 

HEAD CAP SCREWS

If the Outlet valves are not intented to be serviced, continue to page 14

1.  Ensure the dryer is shut down and fully depressurised (See page 8, section 4.1). 

2.  Remove the 8 x M10 socket head cap screws and 8 x washers to release the outlet manifold from the top 

manifold. Figure C.2 

3.  Remove 4 x M10 bolts holding the outlet flange 

4.  Remove the non return valve from the valve orifice within the top manifold and discard. 

5.  Lightly grease and insert the new non return valves into the valve orifices within the top manifold ensuring the 

valve has been insert in the correct orientation. Refer to figure C.2.1 

6.  Place the valve block to the top manifold and insert the 8 x M10 socket head cap screws and the 8 x washers 

to complete the assembly. Refer to page 19-20 and follow the correct tightening sequence when replacing the 
valve block 

7.  Refit the flange 

8.  Start up the Dryer (page 8), or continue to complete service C 

Note Flow Direction on 

the Outlet NRV

TOP MANIFOLD

Figure C.2.1

Summary of Contents for NDL-2110

























Reviews: