background image

P

age 2

GENERAL INFORMATION

Copyright 

This manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied, photocopied, reproduced, 

translated, or reduced to any electronic medium or machine readable form without prior consent in writing from nano 

purification solutions limited. It may not be distributed through the internet or computer bulletin board systems without 

prior consent from nano-purification solutions limited.

©2021 nano purification solutions limited 

Heatless Desiccant Air Dryer: D-Series3 Service Manual 

Models: NDL-2110, 2120,2130, 3130, 4130, 6120, 6130  (Including ES Model) 

Document number: 17-100-0141 

Issue: 001

Document Introduction 

This manual provides manufacturers prescribed procedures for the maintenance and service procedures for a nano 

purification solutions limited compressed air dryer. The procedures illustrated in this document are only to be performed 

by authorised personnel. For further information regarding the procedures outlined in this document contact nano 

purification solutions limited before proceeding. Read this document carefully before attempting to service the dryer. 

General Safety

For your own safety, when carrying out maintenance work on the dryer, all relevant national safety regulations must be 

complied with relating to pressurised and electrical systems. Only authorised, competent and trained personnel should 

maintain the dryer. This user guide is intended solely for such personnel and is to be used only as a reference, it should 

not be used to replace conventional training.

CAUTIONS:

  indicate any situation or operation that may result in potential damage to the product, injury to 

the user, or render the product unsafe.

NOTES: 

highlight important sections of information where particular care and attention should be paid.

Warranty Guidelines

 

All dryers are supplied with a 2 year manufacturer’s warranty from the date of purchase. The dryer should be installed, 

operated and maintained in accordance with the manufacturer’s guidelines. Only genuine service parts should be used 

and no modifications made. For further information please refer to the ‘warranty guidelines’ section on our website: 

www.n-psl.com

Summary of Contents for NDL-2110

























Reviews: