background image

Appendix: CTCSS and DCS chart

● Take out the battery at once when water inlet and dump the water, then keep it dry and 

airiness. And please send it to maintenance station as soon as possible.  

No reaction when power-on

Unable to talk with other 

members in your group

Trouble                                                      

Solution

●The battery pack may have been exhausted. Please replace a new battery or recharge 

the battery.

● The battery pack may be not installed correctly. Please check and install it again.

● Please check the frequency and CTCSS/DCS you use are the same as other members 

use in your group.

● The distance between you and other group members may be too far. Please check if 

you are in the cover range of other group transceivers.

Talking distance is short 

● Make sure the antenna screws tight and contact well

● Make sure if using the original antenna from the manufacturer.

● The dealer or user may set the higher squelch lever, please reduce the lever.

Other (not from group members)

sound heard in channels

● Change the frequency

● Please make sure being changed CTCSS signal of transceiver in all your group  

Battery lasts in a short time after 

recharged

● The use-life of the battery is over, please change new one.

● Make sure the battery is fully charged.

People receive your Voice is not 

clear and loud.

● Check if the MIC hole is jammed.

Water goes into the radio 

20

Summary of Contents for NF-910

























Reviews: