Nakanishi HES810 Operation Manual Download Page 21

40

Refer to the E3000 CONTROLLER and Air Line Kit (AL - C1204) Operation Manuals. 

When disposal of a Brushless Motor Spindle is necessary, follow the instructions from your local 
government agency for proper disposal of industrial components.

Trouble

Cause

Inspection / Corrective Action

Can not set the motor 
speed to its maximum 
allowable speed.

Air Input Monitoring 
Override is set in the 

 

parameter to 

 and 

the motor's maximum 
speed has been limited to 
30,000min

-1

 (rpm). 

Check the setting of parameter 

.

A blinking dot appears 
on Digital Speed 
Indicator. Cannot set the 
desired rotation speed.

Gear Ratio is set to a value 
other than " 1.0 ".

Check the setting of Gear Ratio. 

Overheating during 
rotation.

Cutting debris has 
contaminated the ball 
bearings, and the ball 
bearings are damaged.

Replace the ball bearings.
(Return to NAKANISHI dealer service.)

Low air pressure.

Check air hose connection and air 
pressure.

Abnormal vibration or 
noise during rotation.

The tool shank is bent.

Replace the tool.

Cutting debris has 
contaminated the ball 
bearing.

Replace the ball bearings.
(Return to NAKANISHI dealer service.)

The spindle ball bearings 
have been damaged. 

Tool slippage.

Collet or collet nut are not 
correctly installed.

Check and clean the collet and collet nut. 
Reinstall the collet and collet nut.

The collet and the collet 
nut are worn.

Replace the collet and collet nut.

High run-out.

The tool is bent.

Change the tool.

Collet nut is not correctly 
installed.

Secure the collet and the collet nut 
correctly.

The collet and the collet 
nut are worn.

Replace the collet and the collet nut.

Inside of the spindle is 
worn.

Replace the spindle shaft.
(Return to NAKANISHI dealer service.)

Contaminants inside the 
collet and the collet nut or 
the spindle.

Clean the collet, collet nut and the inside 
of the taper and spindle.

The spindle ball bearings 
have been damaged.

Replace the ball bearings.
(Return to NAKANISHI dealer service.)

DISPOSAL OF THE BRUSHLESS MOTOR SPINDLE

15.

OM-K0587 002_HES810_(A5x18)_EN_150205.indd   40

2015/02/05   17:24:53

Summary of Contents for HES810























Reviews: