manualshive.com logo in svg

Nakanishi HES810, Operation Manual

Share
Download
Nakanishi HES810 Operation Manual Download Page 15

34

<Installation of the provided Lock Bar>

Install the Lock Bar by screwing the Lock Bar into the threaded hole provided on the taper shank as 
shown in Fig. 17.  

Block

Lock Bar

(Provided by 

the customer)

(Standard 

Accessories)

Fig. 19

・

The Lock Bar is not intended to stop the machining center's main spindle from rotating, 

it is only intended to be used as a precautionary measure only. If it is not needed, it is 

not required to be installed.

・

The Block shown in the Fig. 19 is not provided with the Brushless Motor Spindle, it must 

be provided by the customer.

   CAUTION

⑧

Secure the Emergency Connector to the machine, being sure to correctly, horizontally position the 
Emergency Connector and Air Line.

* Route the Motor Cord and Air Hose and hold them securely with enough slack to allow for 

machines' axis travel (Do not pinch and severely bend the air hose) (SEE Fig. 18).
If the positioning and fixation of the Motor Cord and Air Hose are loose, the Emergency 
Connector may not seperate correctly as intended. 

Bolt 

Emergency Air Joint

Emergency Connector

Fig. 18

OM-K0587 002_HES810_(A5x18)_EN_150205.indd   34

2015/02/05   17:24:50

Summary of Contents for HES810























Reviews:

No comments

Brands by name

Popular brands

Load more brands