Naigon Electronic Spark Color SC2-R3 Setup Manual Download | Manualshive

Page: 12 / 33

background image

Page | 12

Figure 7 – Wiring with an RGB crystal chamber. This will have an RGB led that matches the blade color and pulses with the blade. Note that

all three pins of the REB LED have a resistor since power is coming from the battery. I recommend a 22-33ohm for R1, and a 1ohm each for

R2.

4.6.

X-SABER WIRING

The following diagram shows the wiring of the XDrive and Spark Color 2™ board to utilize the X-Saber functionality.
Three NECree LEDs are shown; a TriCree can be used as well but resistors will be needed for all three red die.

Note that it is recommended to use a 26650 since the runtime drain for this setup is quite high.

«
...
10
11
12
13
14
...
»

Summary of Contents for Spark Color SC2-R3


































Reviews:

No comments

Related manuals for Spark Color SC2-R3

Brand: Hama Pages: 76

Brand: Farallon Pages: 40

DF PROFINET IO PCI

Brand: Kunbus Pages: 7

Brand: Asus Pages: 18

Brand: ICP DAS USA Pages: 7

Brand: ICP DAS USA Pages: 8

Brand: Vantec Pages: 11

Brand: pandaboard Pages: 83

Brand: Konig Pages: 30

Brand: Brainboxes Pages: 2

Brand: M-Audio Pages: 35

Brand: Exsys Pages: 2

Brand: Surecom Pages: 4

Brand: Surecom Pages: 37

Brand: MARIAN Pages: 22

Brand: MARIAN Pages: 28

Brand: MARIAN Pages: 66

TransImp TIP-PU301

Brand: MUKii Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands