background image

9

C O N T R O L S A N D C O N N E C T I O N S

5. REAR PANEL

(37) SPEAKER OUTPUTS
• RIGHT - These two 1/4” speaker output jacks are paralleled together for the Master Right output signal and can deliver up to 200W
RMS to a 4

load.

• LEFT - These two 1/4” speaker output jacks are paralleled together for the Left output and can deliver up to 200W RMS to a 4

load.

[Caution:  Never use less than 4

Total impedance for either channel as this can cause the amplifier to overheat and create thermal

runaway.]

(38) POWER ON/OFF SWITCH
To turn the unit on, press the side of the rocker switch closest to the side of the mixer.  To turn the unit off, press the rocker switch
towards the middle of the mixer.

(39) POWER CONNECTOR
The IEC jack is used to connect the power cord to the AC Power Source.  

[Caution: Never remove the center grounding pin as this can cause a serious safety hazard and will immediately void your warranty.]

(40) FUSE COMPARTMENT
Replace with only the same type fuse. If the fuse blows continuously, have the unit serviced by qualified personnel.  The PMX Series
powered mixer uses 20mm glass tube Fast Blow fuses:  8A 250V for 115VAC,  4A 250V for 230VAC.

(41) AC VOLTAGE SELECTOR SWITCH
Before plugging in the power cord, check to see that the unit is set for the proper voltage for your area: ~115V (60Hz) or ~230V
(50Hz).

(39)

(41)

(37)

(38)

(40)

Summary of Contents for PMX series













Reviews: