IDENTIFICATION OF CONTROLS
rear panel
1 ac line cord:
Plug the AC power cord into a live AC wall socket.
Make sure all connections have been made before connecting to mains.
2 hdmi out:
Using a HDMI cable (not supplied), connect the HDMI OUT
jack to the corresponding HDMI input jack of a compatible equipment
like a HDTV, a projector or an A/V Receiver.
WARNING
Before connecting and disconnecting any HDMI cables, both the T 517
and the ancillary source must be powered OFF and unplugged from the
AC outlet. Failure to observe this practice may cause permanent damage
to all equipment connected via HDMI sockets.
IMPORTANT NOTICE
If your HDMI equipped TV is not capable of decoding DTS or Dolby
Digital Bitstream, set the T 517’s Dolby Digital or DTS setting at the
“Audio Setup Menu” to “PCM”. There may be a rushing noise heard if
your TV is not capable of decoding the DTS (or Dolby Digital) Bitstream;
most TVs do not have this capability.
3 S-video out (120v version only):
In general, the S-Video
connection is superior to composite video and should be used if
your TV/monitor provides the corresponding input. Connect to the
corresponding S-Video input of a compatible monitor/television,
projector, A/V receiver or processor using quality S-Video cable
designed for video signals.
4 component video out:
Connect to the corresponding component
video input of a compatible equipment like a monitor/television,
projector, A/V receiver or processor. Be sure to observe consistency in
connecting the appropriate Y, Cb/Pb, Cr/Pr jacks to the corresponding
sources/inputs. Do not rely purely on the color coding of the jacks,
which may not always be consistent among brands.
NOTES
• Only non-copy protected discs can be played back at 720p, 1080i and
1080p resolution. If the disc is copy protected, it will be only displayed at
480i/576i or 480p/576p resolution.
• For 230V version only: Make sure to set the “TV Output Select” to “YPbPr”
for component video output to be available.
5 digital out (optical):
Connect to the corresponding optical
digital input of a compatible device such as CD recorders, receivers,
computer soundcard or other digital processors.
6 ir in:
This input is connected to the output of an IR (infrared) repeater
(Xantech or similar) or the IR output of another component to allow
control of the T 517 from a remote location. Most NAD products with IR
OUT are fully compatible with the T 517.
7 Scart/rgb out (230v version only):
Using a SCART connector
(not supplied), connect to the corresponding SCART/RGB video input
of a compatible video monitor/TV. Be sure to observe the correct
orientation of the SCART/RGB plug.
8 video out:
Connect to the corresponding composite video input of
a compatible monitor/television, projector, A/V receiver or processor
using quality dual-RCA cable designed for video signals.
9 audio out:
This analog audio output can be connected to the
corresponding analog audio input of a compatible equipment like an
amplifier, receiver, TV or stereo system.
10 digital out (coaxial):
Connect to the corresponding coaxial
digital input of a compatible device such as CD recorders, receivers,
computer soundcard or other digital processors.
3
4
5
6
7
8
10
1
2
ATTENTION!
Please make sure that the T 517 is powered off or unplugged before making any connections. It is also advisable to power-down or unplug all associated
components while making or breaking any signal or AC power connections.
9
8
EN
G
LIS
H
FR
A
N
Ç
A
IS
ES
PA
Ñ
O
L
IT
A
LIA
N
O
D
EU
TS
CH
N
ED
ER
LA
N
D
S
SV
EN
SK
A
РУ
СС
К
И
Й
