MyGate Q71S Instruction Manual Download Page 2

Page: 2 / 26

The MyGate Q71S Control Board Installation Manual : Printed 11/02/2013 13:16

Contents

Q71S control board layout ........................................................................................................................ 3

Pre-installation checks .............................................................................................................................. 4

Linking Essential Terminals ................................................................................................................... 5

Connecting the motors to the control board ............................................................................................... 6

Limit Switch - Connecting to the control board .......................................................................................... 6

Photocells ................................................................................................................................................. 7

Photocell positioning .............................................................................................................................. 7

Photocell Wiring .................................................................................................................................... 8

To Use in Closing Cycle ........................................................................................................................ 9

Connecting power to the control board .................................................................................................... 11

Programming the remote control / key-fob .............................................................................................. 12

Saving a new remote controls to the control board to open gates FULLY ............................................ 12

Saving a new remote controls to the control board to open gates as PEDESTRIAN (one leaf opens) . 12

Deleting existing remote controls / key-fobs from the control board ..................................................... 12

Changing the code the key-fob transmits ............................................................................................. 13

Remote Control Receiver .................................................................................................................... 14

Extended Aerial

– (optional accessory) ................................................................................................... 14

Fitting the Extended Aerial ................................................................................................................... 14

Selecting the Operating Mode ............................................................................................................. 15

Programming the gates open & closing cycles ........................................................................................ 16

Programming - Single Sliding Gate ...................................................................................................... 16

Setting the Pause Time ....................................................................................................................... 17

Obstacle Detection .............................................................................................................................. 17

Adjusting Obstacle Detection Sensitivity during Normal Opening / Closing Cycle ................................ 18

Adjusting Obstacle Detection Sensitivity during the Deceleration Phase of the Opening / Closing Cycle
............................................................................................................................................................ 18

Appendix: A ............................................................................................................................................ 21

Q71S connection map

– terminals 1 to 21 ........................................................................................... 21

Q71S control board

– FAQ’S ............................................................................................................... 22

Comments & Feedback ........................................................................................................................... 26

Summary of Contents for Q71S



























Search results

Summary of Contents for Q71S

Reviews:

Related manuals for Q71S

Brands by name

Popular brands

MyGate Q71S, Instruction Manual

Search results

Summary of Contents for Q71S

Reviews:

Related manuals for Q71S

Brands by name

Popular brands