manualshive.com logo in svg

MYERSON FlexPress, Instruction Manual, Page: 4 / 24

Share
Download
MYERSON FlexPress Instruction Manual Download Page 4

section 2 ~ storage & handling

The 

myerson

 

Flexpress

™ Digital Injection System should be stored in a 

cool dry place. The unit should not be used in an environment exceeding 
40°C (104°F). Keep all combustibles away from unit while in use. Never 
place anything on the top of the unit. 

section 3 ~ basic operation

Place the 

myerson

 

Flexpress

™ Digital Injection System on a clean dry 

surface. Insert the power cord into the receptacle on the side of the unit 
and plug the other end into a grounded 120V or 230v outlet.

To turn on the unit, press the rocker switch located on the left side of the 
unit above the power cord receptacle. The control panel will illuminate 
briefly then turn back off. The 

myerson

 

Flexpress

™ is now in Standby 

mode. To turn on the controller press the 

ON/STBY

 button (lower left  

button). Below is what you should see in the blue LCD display.

From the Main Menu you can select any of 5 options by using the 

UP & 

DOWN

 arrow keys. Below is the list of options & a description for each:

1. 

Run Stored Profile

- 

myerson,LLC

 pre-programs the myerson  

 

Flexpress

™ with processing parameters for myerson 

DurAceta

l

®

,    

 

myerson

 

DuraFlex

 and 

myerson

 

VisiClear

™. By selecting the pre- 

 

programmed material, the Melt Temp, Melt Time and Hold Time are   

 

already set for you. This is the recommended option to use when 

 

processing cases using the 

myerson

 

Flexpress

™. There is also (3)   

 

“Spare” locations for the customer to save their own settings.

2. 

Rerun Last Profile

- By selecting this option the myerson 

 

Flexpress

™ will run the last set profile. This option is great when

 

processing several cases of the same material.

3. 

Edit User Profiles

- This option is where you can create your own

 

processing profiles and save them for future use. The

 myerson 

 

FlexPress

 is capable of storing up to 7 unique processing profiles.

4. 

Edit User Settings

- This option allows you to change settings 

 

such as temperature units (C/°F), turn off/on alarms, languages, etc. 

6. 

Configure from PC

- This option is used by repair personnel in  

 

 

the event of a warranty repair of the 

myerson

 

FlexPress

.

4

Summary of Contents for FlexPress

























Reviews:

No comments