manualshive.com logo in svg

MYERSON FlexPress, Instruction Manual, Page: 2 / 24

Share
Download
MYERSON FlexPress Instruction Manual Download Page 2

Installation of the Heat Guard 

2  

Section 1   Components 

3

Section 2   Storage & Handling 

4

Section 3   Basic Operation 

4

Section 4   Editing User Profiles 

 

Section 5   Processing using the “Run Stored Profile” 

5 

 

option (Recommended Option)

Section 6   Processing using the “Rerun Last Profile”  
Section 7   Myerson DuraFlex Partial Injection Procedure 

7

Section 8   Myerson DurAcetal Framework Injection Procedure  14 
Section 9   Warranty & Returns 

19

Section 10   Technical Data 

19

Section 11   Preventative Maintenance & Cleaning 

20

Section 12   Service & Repairs 

20

Section 13   Declaration of Conformity 

19

Section 14   Important Safety Warnings 

21

Section 15  Notes 

22

Installation of the HEAT GUARD

To prevent damage, the 

myerson

 

FlexPress

™ has been shipped 

with the heat guard not installed. To install the heat guard, place  
the heat guard over the corner posts with the warning label UP. 
Install the (4) black acorn nuts finger tight. The acorn nuts are 
simply holding the heat guard down, so they do not need to be 
wrenched tight.

The heat guard can be removed periodically for cleaning.  
Just follow the above steps in reverse order to remove the 
heat guard.

Thank you for your purchase. Feel free to call myerson with 
any questions. 

2

Summary of Contents for FlexPress

























Reviews:

No comments