MYERSON FlexPress Instruction Manual Download Page 20 | Manualshive

Page: 20 / 24

MYERSON FlexPress Instruction Manual Download Page 20

20

Section 11 ~

preventive maintenance & cleaning

Use only approved materials in the

myerson

Flexpress

™ Digital

Injection System. The use of other materials may cause the unit to fail
and will void the manufactures warranty. See Section 10 for warranty
information.
Keep heating chamber and flask area free from dirt and other foreign
debris to prolong the life of the unit. Periodically clean the heating
chamber with the cleaning brush. The rest of the unit can be cleaned
with a damp rag and mild soap solution. Turn off and unplug the unit
before cleaning. Always keep the unit in an upright position.

Section 12 ~ Service & Repairs

For service and repair of the

myerson

Flexpress

™ Digital Injection

System, please call

888.401.1126

or go to cdmdental.com.

For technical support contact

Kris Schermerhorn

CDT

at

800.874.1047

or email at

[email protected]

Section 13 ~

Declaration of Conformity

Use only approved materials in the

myerson

Flexpress

™ Digital

Injection System. The use of other materials may cause the unit to
fail and will void the manufactures warranty. See Section 10 for
warranty information.

Keep heating chamber and flask area free from dirt and other foreign
debris to prolong the life of the unit. Periodically clean the heating
chamber with the cleaning brush. The rest of the unit can be cleaned
with a damp rag and mild soap solution. Turn off and unplug the unit
before cleaning.

Always keep the unit in an upright position.

«
...
18
19
20
21
22
...
»

Summary of Contents for FlexPress

























Reviews:

No comments