MuxLab 500732 Installation & Operation Manual Download Page 18 | Manualshive

Page: 18 / 32

background image

© MuxLab Inc.

6G-SDI Extender Over FIBER

Page 18

4.

Firmware Upgrade

Procedure

4.1.

Firmware Upgrade Procedure

1.

Make sure the PC USB device driver has been
installed (see section 4.2 for more details)

2.

Download the latest version of the appropriate
firmware upgrade from the MuxLab website.

3.

Unzip the firmware upgrade executable in a
directory of your choice.

4.

Connect the mini-USB cable to the unit and to
the PC.

5.

When the device driver has recognized your
device to be upgraded you can double click on
the upgrade application to execute it.

«
...
16
17
18
19
20
...
»

Summary of Contents for 500732

































Reviews:

No comments

Related manuals for 500732

Brand: Sage Pages: 84

Brand: Sage Pages: 16

Brand: DVIGear Pages: 10

Brand: Russell Hobbs Pages: 12

Brand: StarTech.com Pages: 14

PROSTICK 1500 MURDUM AR 1053

Brand: Arzum Pages: 44

Brand: Tributaries Pages: 8

Brand: Globalmediapro Pages: 9

Brand: AFi Pages: 8

Compact Food Processor

Brand: Morphy Richards Pages: 8

Brand: Black & Decker Pages: 8

ProBlend BL5001

Brand: Black & Decker Pages: 2

Brand: Black & Decker Pages: 8

ProBlend MTB500

Brand: Black & Decker Pages: 2

Brand: Black & Decker Pages: 12

Power Pro BLP14600DG

Brand: Black & Decker Pages: 2

Cyclone BLC12650H

Brand: Black & Decker Pages: 19

Brand: Black & Decker Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands