MUTOH UniFixer 65 User Manual Download Page 63 | Manualshive

Page: 63 / 66

background image

User’s Guide Unifixer 65

Periodical maintenance

AP-75393 - Revision 1.1

63

6

Chapter 6 Periodical

maintenance

This chapter describes the periodical services required on a Unifixer 65. The periodical
services ensure a stable quality of the machine.
In the periodical services, some parts need to be checked, cleaned or replaced by the end
user or by an authorized Mutoh technician

6.1

Done by the end user.

Note



Please use Original Mutoh spare parts.



Any problems caused by use of non-original Mutoh spare parts or other
consumables will not be covered by the warranty.

Frequency

Component

Action

Immediately

Ink waste on the felt belt

Let the machine run at working
temperature until the remaining
ink disappears on the felt belt

Weekly

Felt belt

Gently wash with water and soap



Make sure it is completely dry
before using again.

Cleaning the felt belt on page 64

Feeding table

Gently wash with water and soap



Make sure it is completely dry
before using again.

Tension bars

Gently wash with water and soap



Make sure it is completely dry
before using again.

Metal body

Gently wash with water and soap

«
...
61
62
63
64
65
...
»

Summary of Contents for UniFixer 65



































































Reviews:

No comments

Related manuals for UniFixer 65

Brand: DataCard Pages: 2

Brand: Oki Pages: 572

proColor pro900DP

Brand: Oki Pages: 127

Brand: Olivetti Pages: 309

Brand: OKIDATA Pages: 4

Brand: Ricoh Pages: 682

Brand: Rokit Pages: 16

Brand: Partner Pages: 15

Brand: GCC Technologies Pages: 8

3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...

Brand: 3Com Pages: 94

Brand: Planmeca Pages: 56

Brand: Anyload Pages: 12

Brand: Go Pages: 3

Brand: Avery Dennison Pages: 68

Brand: Wasp Pages: 82

Brand: Roland Pages: 116

Brand: HandTop Pages: 97

Automatic Photo Book Station

Brand: Durst Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands