MUTOH UniFixer 65 User Manual Download Page 46 | Manualshive

Page: 46 / 66

background image

User’s Guide Unifixer 65

Basics

46

AP-75393 - Revision 1.1

Step 13:

Place the transfer paper flat on the table with equal tension to the left and right side.

Step 14:

Carefully insert the transfer paper until it is being grabbed by the belt and protection
paper.

Note



Make sure that the printed side of the transfer paper is facing up.

«
...
44
45
46
47
48
...
»

Summary of Contents for UniFixer 65



































































Reviews:

No comments

Related manuals for UniFixer 65

Brand: Creality Pages: 24

VarioPrint 4110

Brand: Oce Pages: 216

Brand: Olivetti Pages: 228

Brand: Buffalo Pages: 2

BROTHER HL-630 OPC

Brand: Summit Pages: 46

Brand: Ricoh Pages: 130

Pro C5300 Series

Brand: Ricoh Pages: 37

Brand: Airlink101 Pages: 36

Brand: Epson Pages: 4

Brand: WOOSIM Pages: 19

Brand: WOOSIM Pages: 20

Brand: Hitachi Pages: 11

Brand: Hitachi Pages: 62

Brand: Hitachi Pages: 88

Brand: Hitachi Pages: 165

Brand: Hitachi Pages: 355

Brand: Hitachi Pages: 231

Brand: Hitachi Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands