MUTOH UniFixer 65 User Manual Download Page 38 | Manualshive

Page: 38 / 66

background image

User’s Guide Unifixer 65

Basics

38

AP-75393 - Revision 1.1

5.1.2 Powering

OFF

Step 1:

Set the heater temperature as low as possible.

Refer to

Operation panel on page 34

Step 2:

Increase the rotation speed of the felt belt to the maximum and let the machine cool
down for 10 minutes.

Step 3:

Switch off the power switch located at the back of the machine.

Note



Make sure no objects such as protection paper, transfer paper or fabrics are on
or near the Unifixer 65.



Due to static electricity, it might happen that the protection paper, transfer
paper or fabric is being pulled into the machine again.

Note



The machine may be switched off while the temperature is still hot, but this is
not recommended.

«
...
36
37
38
39
40
...
»

Summary of Contents for UniFixer 65



































































Reviews:

No comments

Related manuals for UniFixer 65

imagePROGRAF iPF760

Brand: Canon Pages: 12

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 16

imagePRESS C850

Brand: Canon Pages: 146

imagePRESS C850

Brand: Canon Pages: 63

imagePROGRAF iPF760

Brand: Canon Pages: 132

imagePROGRAF iPF825 MFP Basic Guide No.1

Brand: Canon Pages: 8

imagePROGRAF TX-2000

Brand: Canon Pages: 14

i-SENSYS MF6180dw

Brand: Canon Pages: 1040

imagePROGRAF iPF815

Brand: Canon Pages: 48

imageRUNNER 1025

Brand: Canon Pages: 6

imageRUNNER 2230

Brand: Canon Pages: 6

IMAGEPRESS C7010VPS

Brand: Canon Pages: 388

Brand: Canon Pages: 56

imagePROGRAF iPF8300

Brand: Canon Pages: 24

imagePROGRAF iPF8300

Brand: Canon Pages: 4

imagePROGRAF iPF6350

Brand: Canon Pages: 12

imagePROGRAF iPF6350

Brand: Canon Pages: 2

imageCLASS MF8380Cdw

Brand: Canon Pages: 192

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands