background image

INSTALLATION:

1.   

Provide rough-ins as shown in Roughing-In and Dimensional Drawing.

2.   

Anchor water cooler to wall through anchor clips on the bottom of the base.

7.   Assemble bottom cover to water cooler with screws furnished. 

2.   Air within the water cooler system or the structure supply piping will cause an irregular bubbler outlet stream 

until purged out by incoming water. Covering the bubbler with a clean cup (or similar object) is recommended 
when first activating water cooler to prevent excessive splashing. Depress the pushbutton until steady water 
stream is achieved.

6.   Plug water cooler in to electrical outlet and make sure unit begins to function.

START UP:

1.   Before connecting power supply and assembling bottom cover to water cooler, but after thoroughly flushing 

the supply line and connecting it to the fixture, turn on building water supply and check all connections for 
leaks.

4.   Recheck all water and drain connections with water flowing through system.

5.   With power still NOT connected, carefully manually rotate cooling fan to insure proper clearance and free fan 

action.

3.   If water flow requires adjustment, insert a slotted narrow blade screwdriver through the hole centered on the 

pushbutton to the flow regulator. Turning clockwise will increase flow and turning counterclockwise will 
decrease flow.

4.   After thoroughly flushing the 3/8” O.D. supply line, connect water supply to water cooler.

5.   Make up 1-1/4” O.D. P-Trap waste connection.

3.   

Remove the front panel from the water cooler by taking out the screws on each side at the bottom front, press 

the panel sides together at the bottom so that front panel clips disengage from the housing sides and carefully 
pull forward and down. Set panel aside in a safe place where it will not be damaged.

 

A511.5

Page 3 of 9

RVA 

05/28/21

7020-921-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 WATER COOLERS

 

Summary of Contents for A511.5 Series










Reviews: