background image

 

 

A131-VR

Page 10 of 12

New: 10/28/2020

7021-012-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

CARTRIDGE VALVE PARTS BREAKDOWN

3

2

1

5

4

Note: Use the Universal Maintenance Tool to perform the following:

 NOTE: STRAINER SCREEN MUST BE IN PLACE FOR WATER TO FLOW.

 

1. Strainer Plug must be removed before Cartridge replacement and Strainer maintenance (no need to turn the 

water off at the Angle Stop). Some residual water will drainduring Plug removal.

3. Cartridge Replacement - insert diamond end of the Universal Tool into Pushbutton, rotate 90 degrees and pull 

firmly to remove the Button. Remove Cartridge Retaining Nut . Remove and replace Cartridge. When replacing 
Cartridge, be sure to align the inlet and outlet Ports on the Cartridge with the Ports in the Valve Body.

CARTRIDGE REPLACEMENT/ STRAINER MAINTENANCE 

2. Clean Strainer as needed using clean water.

Universal Maintenance Tool

-Button Removal
-Cartridge Retaining Nut
-Strainer Plug
-Removal of P.E. Tubing from
 Push-in Fittings

6

ITEM #

PART NUMBER DESCRIPTION

1

7003-095-000

Valve Body Sub Assembly

2

7000-060-000

Valve Cartridge

3

7000-052-000

Retaining Nut

4

7003-864-000

Strainer, Auto Stop

5

7003-097-001

Strainer Cap

6

7003-194-199

Maintenance Tool

 

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 DRINKING FOUNTAINS

 

Summary of Contents for A131-VR Series













Reviews: