background image

 

A131-VR

Page 6 of 12

New: 10/28/2020

7021-012-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

IMPORTANT:

 1.  Water Supply Service Stop Valve and Water Connections to be supplied by others in accordance with local 

codes.

 2.  Waste is 1-1/4” Outer Diameter. Drinking Fountain water inlet is 3/8” Outer Diameter copper tube. Bottle 

Filler water inlet is 3/8” Outer Diameter copper tube. Water line by others.

 3.  Completely flush supply lines of all foreign debris before connecting to fixture. Optional Water Filter (WF1), is 

available should any problems with taste, odor, color, or sediment arise from the water supply.

4.  All burrs must be removed from outside of cut tubes before inserting into strainer or other components.

 5. 

Per UPC 609.10-All building water supply systems in which quick acting valves are installed shall be 
provided with devices to absorb the hammer caused by high pressure resulting from the quick closing of the 
valve. These pressure-absorbing devices shall be approved mechanical devices. Water pressure-absorbing 
devices shall be installed as close as possible to the quick closing valve.

PRIOR TO INSTALLATION:

1. Read all installation instructions carefully, before proceeding.

5. Completely flush water supply lines of all foreign debris, before connecting to the fixture.

8. After thoroughly flushing the 3/8” outer diameter supply line, connect water supply to the 3-way divider 

assembly. From the 3-way divider assembly, connect to drinking fountain bubbler.

4. Remove the drinking fountain top by taking out the drain screw and lifting at the front while pulling forward. 

Disconnect bubbler tube. Set top aside in a safe place where it will not be damaged. Place the screw in a 
secure location where it will not be lost.

2. Hang trim panel on mounting frame. Note: The included 1” brackets do not get used with this installation and 

the plastic spacers are typically not required and can be discarded.

3. 

If water flow requires adjustment, insert a slotted narrow blade screwdriver in the hole centered on the 

underside of the fixture in the knee clearance area up to the flow regulator. Turning clockwise will increase 
flow and turning counterclockwise will decrease flow.

2. Carefully remove all fixture components  from packaging, preventing scratching or damage. Inspect fixture and 

all parts from damages and all parts that are bolted on.

7. Make-up 1-1/4” outer diameter waste connection.

DRINKING FOUNTAIN START UP:

1. Insert mounting frame into the rough-in block out and secure using 1/4”-20 UNC mounting hardware (Provided 

by Others).

3. Provide mounting surface, adequate to support the fixture and loads on the fixture.

6. Assemble P-trap to drain adapter and then assemble to unit with Phillips head screws.

2. 

Air within the drinking fountain system or the structure supply piping will cause an irregular bubbler outlet 

stream until purged out by incoming water. Covering the bubbler with a clean cup (or similar object) is 
recommended when first activating drinking fountain to prevent excessive splashing. Depress front push pad 
until steady water stream is achieved.

1. 

Before connecting power supply, but after thoroughly flushing the supply line, turn on building water supply 

and check all connections for leaks.

4. 

Recheck all water connections with water flowing through system.

4. Provide rough-ins as shown on the roughing-in and dimensional drawing, including water supply, drain pipe 

and gravel drain well. (See rough-in details)

9. Place drain gasket on drain adapter. Reconnect bubbler tube. Reassemble top to unit by engaging back clip 

and securing with screw.

DRINKING FOUNTAIN INSTALLATION:

3. Install the four threaded studs into the Wall Mounting Frame

5. Slide Fixture over studs and secure with nuts and washers.

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 DRINKING FOUNTAINS

 

Summary of Contents for A131-VR Series













Reviews: