manualshive.com logo in svg

Muonio SE1, Manual

Share
Download
Muonio SE1 Manual Download Page 21

Wiring examples - Y plan heating

Heating ON, DHW ON - This is similar to the prevous case, but the white liver also becomes live. This means that the 

valve will move to the mid position and hot water will be supplied to both the heating and the DHW zones.  

Heating ON, DHW OFF - Grey wire (Hot water off) is live, White wire (heating on) is live. The valve will move to the 

heating only position. When the valve is in position the end switch will close and the orange wire will become live, this 

will fire the boiler through the beridge between SL and AUX_L.

Y PLAN HEATING SOFTWARE SETTINGS 

SOFTWARE SETTINGS EXPLAINED.
The software settings are the same as for the S-Plan example above. Relay 

3 is dedicated to heating and Relay 2 is for domesitc hot water. Again, Relay 

1 is not selected for heating or hot water because we want the boiler call 

signal to come from the valve when the valve reaches its desired position. 

FIGURE 24.   Y PLAN SOFTWARE  
    

SETTINGS

OPTIONAL WIRING FOR Y PLANS
If your system doesn’t have a DHW sensor installed the SE1 can still control 

the DHW, but without temperature control. From the app you will be able 

to turn DHW generation ON/OFF, or you can set up an hourly schedule for 

DHW generation. For this kind of system you will need a DHW Thermostat/

High Limit Thermostat connected between terminal T_L  and T_SL. This is to 

make sure that the DHW generation stops when the hot water reaches the 

desired temperature. This thermostat is not only important to save energy and 

prevent scalding, but also to prevent the water from boiling which can cause 

overpressure in the system.

FIGURE 25. OPTIONAL WIRING FOR Y 

Do not wire an immersion heater to the SE1. The relay board is not designed for such high outputs. If 
you need to control an immersion heater for DHW you have to use an additional relay. 

DHW Thermostat 

and/or

High Limit Thermostat

Orange (Boiler and pump live)

Blue (Neutral)

C

2

1

SE1 DEVICE  SETT INGS

SETUP BOARD

REMOVE

EDIT

BLINK

HOT WATER

YES

NO

RELAY 1 CALL

YES

NO

ZONE 1 KITCHEN

RELAY  1R

ELAY 2  

HOT WATER 

RELAY3

RELAY 5

RELAY 4

RELAY  1R

ELAY 2  

HOT WATER 

RELAY3

RELAY 5

RELAY 4

HEATING 

COOLING

Summary of Contents for SE1































Reviews:

No comments

Brands by name

Popular brands

Load more brands