background image

 BPX GASOLINE VIBRATOR • OPERATION AND PARTS MANUAL — REV. #1 (08/28/17) — PAGE 19

BEFORE STARTING

Before starting the BPX Gasoline Vibrator, perform the 

following:

 

„

Read the safety instructions at the beginning of this

manual.

 

„

Clean the engine, removing dirt and dust, particularly

the engine cooling air inlet, carburetor, and air cleaner.

 

„

Check the air filter for dirt and dust. If the air filter is dirty,

replace it with a new one.

 

„

Check the carburetor for external dirt and dust. Clean

with dry compressed air.

 

„

Check all fastening nuts and bolts for tightness.

 

„

Check the engine oil level.

 

„

Check the fuel level.

 

„

Check the tension and condition of the V-belt.

INITIAL START-UP

This section is intended to assist the operator with the initial 

start-up of the BPX vibrator. 

It is extremely important to 

read this section carefully before attempting to use the 

vibrator in the field.

Starting the Engine

1. Move the engine fuel valve lever (Figure 8) to the

ON position.

Figure 8. Engine Fuel Valve Lever (ON)

2. If starting a 

cold engine, or if the ambient temperature 

is cold,

 

place the choke lever in the 

CLOSED position

(Figure 9).

Figure 9. Engine Choke Lever (Closed)

3. If starting a 

warm engine, or if the ambient temperature 

is warm,

 

place the choke lever in the 

OPEN position

(Figure 10).

Figure 10. Engine Choke Lever (Open)

OPERATION

Discount-Equipment.com

Summary of Contents for BPX













































Reviews: