MultiDyne SilverBack V Configuration And Operation Manual Download Page 24

Page: 24 / 64

SilverBack V Camera-Mountable Fiber Optic Transmission System

Made in the USA

Page

Control Panel Navigation

MENU/ENTER

•

Press to open display main menu.

•

Press again to select feature

UP/DOWN Arrow Buttons

•

Use to navigate control panel Status pages and sub menus.

TALLY Indicator

•

Illuminates when camera is live.

TALK 1 & 2

•

TALK buttons provide momentary or latching PTT functionality for channels 1 and 2, either
separately or simultaneously.

CH1, CH2 and PGM + or –

•

Adjust intercom or program audio volume in the headset.

•

LEDs indicate presence of intercom or program audio on each channel.

•

Determines which video signal is being sent to the viewfinder. This could be either the camera
output or the return sent by the base unit.

CAM

•

Illuminates when receiving camera output.

RET

•

Illuminates when receiving base unit signal.

Summary of Contents for SilverBack V

































































Search results

Summary of Contents for SilverBack V

Reviews:

Related manuals for SilverBack V

Brands by name

Popular brands

MultiDyne SilverBack V, Configuration And Operation Manual

Search results

Summary of Contents for SilverBack V

Reviews:

Related manuals for SilverBack V

Brands by name

Popular brands