background image

Program Control Mode "Programs"

Press the 'M-button' to select operation modes under the preset 

programs. 

While in the 'Programs' mode, the display shows a character to 

indicate a specific program and a digit to indicate the program's 

number. 

Select a desired program by rotating the Manipulator. 

Press the center of the Manipulator for one time to start the rotation. 

Attention! 

The rpm rates and the programs cannot be changed on 

the go. Stop the rotation to change a program. While a program is in 

operation, it is only possible to change the rotational direction by 

pressing the center of the Manipulator for two times at a run same as 

you double-click on a computer mouse. 

Very important! 

Follow the safety precautions!  

It is allowed to unlock the clamp or to change a tool only after the 

rotation is fully stopped.  

17

1. To switch on the rotation, press the center of the Manipulator 

once

2. To increase the rpm rate, rotate the Manipulator clockwise

3. To decrease the rpm rate, rotate the Manipulator counterclockwise

4. To alter the rotational direction (the reverse function), press the 

center of the Manipulator twice at a run same as you double-click on 

a computer mouse

5. To switch off the rotation, press the center of the Manipulator once 

again

You can change the rpm rates and the rotational directions 

on the go.  

Summary of Contents for Podolog

























Reviews:

Related manuals for Podolog