IN CASE OF TROUBLE
Your new subwoofer, once set-up and adjusted, should give you years of listening enjoyment with
your favorite movies and music. However, if you should experience a problem with your unit, the
following chart should help you locate the trouble:
Problems
Diagnosis
1)
Subwoofer makes loud noise at turn-on.
A)
Muting circuit is defective. Return unit for repair.
2)
Subwoofer has no output.
a)
Status LED off
A)
Line cord is not plugged in.
B)
Line fuse is blown. Unplug line cord from wall
outlet, then check fuse.
C)
Internal fuse is blown. Return unit for repair.
b)
Red light on
A)
No signal is reaching the unit. Check
connections from receiver or preamplifier.
B)
Power switch is turned off. Place switch to
“stand by” or “on” mode.
c)
Green light on
A)
Signal is present, but input level control is set
at minimum.
3)
Subwoofer has little output.
A)
Input level control is set too low.
B)
If using high level inputs, right and left channels
are connected out of phase. Check wiring.
4)
Subwoofer output is distorted at high volume.
A)
Volume of subwoofer is too high, causing
amplifier to be over driven. Reduce setting of input
level control.
B)
Signal from receiver, amplifier, or preamplifier
is distorted from being over driven. Reduce main
system volume or bass tone control.
C)
Subwoofer electronics are defective. Return
unit for repair.
5)
Subwoofer output is distorted at low volume.
A)
Signal from receiver, amplifier, or preamplifier is
distorted from defective electronics.
B)
Signal connecting wires to subwoofer are
shorted. Check wiring.
C)
Subwoofer electronics are defective. Return
unit for repair.
6)
Subwoofer makes hum or buzzing noises.
A)
Grounding problem or ground loop condition.
Check wiring.
B)
Isolate problem by removing all connecting
cables and turning up subwoofer input level
control. If noise is still present, subwoofer
electronics are defective. Return unit for repair.
ESPECIFICACIONES
Tipo de amplificador:
Clase A/B
Respuesta de Frecuencia:
48Hz – 160HZ
Crossover de pase bajo:
60Hz – 160Hz a 18dB por octava
Entradas:
Nivel lineal y nivel de bocina de rango completo
Salidas:
Nivel lineal y rango completo
Filtro sub-sónico de pase alto:
18 dB por octava debajo de 30Hz.
Interruptor de polaridad:
Normal (0 grados)/reversa (180 grados)
Amplificador
Poder: (continuo)
100 watts
Driver
Tamaño:
8” (203.2mm.)
Diámetro de la bobina:
1” (25.4mm)
Medidas:
Alto:
7” (177.8mm)
Ancho:
23 ¾” (603.3mm)
Profundidad:
12 ¼” (311.2mm)
Huella normal:
12 ¼” (311.2mm.) x 23 ¾” (603.3mm)
Huella de montado de lado:
7 ½” (190.5mm.) X 23 ¾” (603.3mm.)
Peso
Sistema:
20lbs. (9.1Kg.)
Embarque:
24lbs. (10.9Kg.)
Las especificaciones pueden cambiar sin previo aviso.
ASISTENCIA TECNICA
Para obtener asistencia adicional puede visitar nuestra página web www.mtx.com. O puede llamar al teléfono
1-800-CALL-MTX o por E-mail: [email protected].
10
21
ENGLISH
