background image

WIRING UP THE Z-4000 TRANSFORMER

The Z-4000 contains connectors that are designed to accept banana jack
connectors or may be used as traditional screw down binding posts at the back of
the transformer case. Each connector is color coded, BLACK for ground (-) and
RED for positive (+) connections. The top row of connectors are BLACK and
act as common ground connections for each output, while the bottom row of
connectors are RED and provide the positive connection for each output.
Connect the BLACK or ground terminal to either outer rail of the track and the
RED or positive terminal to the center rail of the track. Wiring the constant
voltage outputs (used for accessories) follows the same convention.

Once the track and/or accessories have been wired up to the Z-4000, plug the AC
power cord into any 110V household plug and follow the remaining operating
instructions.

Note: The owner should not, at any time, attempt to connect or short any of the voltage outputs
together in an effort to gain more power output. If the user attempts such a procedure, the Z-
4000 may become permanently disabled. At the very least, the Z-4000 will automatically shut
down and the red OVERLOAD light will be illuminated.

Also functions as a binding post.

Connect To

Outside (-) Rail

Connect To

Track Center (+) Rail

3

Z-4000 Transformer Operating Manual

Summary of Contents for Z-4000















Reviews: