MTHTrains Z-4000 Page 13 Operating Instructions Manual Download | Manualshive

Page: 13 / 14

background image

FCC REGULATIONS

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference with radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures: reorient or relocate the receiving antenna, increase the separation
between the equipment and receiver, connect the equipment into an outlet on a
circuit different from that to which the receiver is connected, consult the dealer or
an experienced radio/TV technician for help. Any changes or modifications not
expressly approved by M.T.H. ElectricTrains could void the user’s authority to
operate this equipment in the USA.

13

Z-4000 Transformer Operating Manual

«
...
11
12
13
14
»

Summary of Contents for Z-4000















Reviews:

No comments

Related manuals for Z-4000

Brand: Canon Pages: 58

Brand: LAUREL Pages: 28

Brand: HBK Pages: 40

Brand: HBK Pages: 104

Brand: Rough and Ready Pages: 14

Brand: Paso Pages: 32

Brand: Bear TA Pages: 4

HUMICAP HMW90 SERIES

Brand: Vaisala Pages: 118

King-Gage 5800 Series

Brand: NOSHOK Pages: 12

Brand: AVGear Pages: 16

Brand: Vaisala Pages: 64

Brand: Icom Pages: 10

Brand: C4Line Pages: 2

Brand: Z-CAR Pages: 3

TEK-W AVE 4300C

Brand: TEKTROL Pages: 35

Brand: Humminbird Pages: 2

Brand: Walter Dittel Pages: 30

FMT5.0-2U Series

Brand: Warner RF Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands