MTD 769-11837A, Operator'S Manual

Page: 11 / 40

Controls & Operation
3
11
(A)
(C)
(D)
(E)
(J)
(K)
(A)
(B) (B)
(F)
(G)
(J)
(K)
(L) (L)
(M)
(M)
(N*) (N*)
(O)
(P)
(P)
(I)
(H)
Hydro Transmission
30” 6-Speed Transmission 24” 6-Speed Transmission
(F)
(H)
(I)
(B)
(K)
(J)
(N*)
(M)
(P)
(N*)
(N*)
* -- Refer to Oil Fill Cap for location of your oil fill cap.
Figure 3-1
Note: This Operator’s Manual covers several
models. Riding mower features may vary by
model. Not all features in this manual are
applicable to all riding mower models and the
riding mower depicted may differ from yours.
Note: References to LEFT, RIGHT, FRONT, and REAR
indicate that position on the riding mower when
facing forward while seated in the operator’s seat.
Throttle/Choke Control or Throttle
Control Lever (If equipped) (A)
Throttle/Choke Control Lever (If equipped)
The throttle/choke control lever is
located on the left side of the riding
mower’s dash panel. This lever controls
the speed of the engine and, when
pushed all the way forward, past the
detent position closes the choke for
cold starting. When set in a given
position, the throttle will maintain a
uniform engine speed.
Note: When operating the riding
mower with the cutting deck engaged,
be certain that the throttle/choke
control is always in the FAST
position.
Throttle Control (If equipped)
The throttle control is located on the
left side of the riding mower’s dash
panel. When set in a given position,
a uniform engine speed will be
maintained.
Push the throttle control handle
forward to increase the engine speed.
The riding mower is designed to
operate with the throttle control in the
FAST
position (full throttle) when
the mower deck is engaged.
Pull the throttle control handle
rearward to decrease the engine speed.
FAST
SLOW
FAST
SLOW
Ignition Module (B)
WARNING
Never leave a running machine unattended. Always
disengage PTO, set parking brake, stop engine and remove
key to prevent unintended starting.
The ignition module is located on the left fender of
the riding mower seated in the operator’s position,
adjacent to the throttle/choke control or throttle
control.
Ignition Module w/ Reverse Caution Mode (If
equipped)
To start the
engine, insert
the key into
the ignition
switch and turn
clockwise to
the START
position. Release
the key into
the NORMAL
MOWING MODE
position
once the engine
has fired.
To stop the engine, turn the ignition key
counterclockwise to the STOP
position.
CAUTION
Prior to operating the riding mower, refer to both Safety
Interlock Switches and Starting The Engine in the Operation
section of this manual for detailed instructions regarding
the Ignition Switch Module and operating the riding mower
in REVERSE CAUTION MODE
.
Ignition Module (If equipped)
The ignition switch has three
positions:
STOP — The engine and
electrical system is turned off.
RUN — The riding mower
electrical system is energized.
START — The starter motor will turn over the
engine. Release the key immediately when the
engine starts
Note: To prevent accidental starting and/or battery
discharge, remove the key from the ignition switch
when the riding mower is not in use.
Forward Drive Pedal (Hydro riding
mowers) (C)
The forward drive pedal is located on the right
side of the machine, along the running board.
Press the forward drive pedal forward to cause the
riding mower to travel forward. Ground speed is
also controlled with the forward drive pedal. The
further forward the pedal is pivoted, the faster the
riding mower will travel. The pedal will return to its
original/neutral position when it’s not pressed.
Reverse Drive Pedal (Hydro riding
mowers) (D)
The reverse drive pedal is located on the right
side of the riding mower along the running board.
Ground speed is also controlled with the reverse
drive pedal. The further downward the pedal is
pivoted, the faster the riding mower will travel. The
pedal will return to its original/neutral position
when it’s not pressed.