MSA Ultima MOS-5 Instruction Manual Download Page 65

Page: 65 / 68

Ultima MOS-5 Detector

9.3.4 Environmental

Specifications

9.4 Approvals

CE Marking; CSA, FM, ATEX, IECEx and GOST approved. Complies with ANSI/ISA-
92.0.01:1998, performance requirements. SIL 2/3 suitable (

use in typical environments has

a lower safety rating than in clean environments

). HART Registered.

HART:

•

Approved by the HART Communication Foundation.

•

Compatible with Emersion 375 Field Communicator.

•

Listed in Emerson Process Management’s Aware device list.

9.5 Spare Parts and Accessories

To order spare parts and/or accessories, please contact the nearest MSA Representative or,
MSA directly, and give the following information:

•

Part Number of Spare Part or Accessory

•

Description of Spare Part or Accessory

•

Quantity of Spare Part or Accessory

9.5.1 Sensors

50445-1

0 to 100 ppm, Aluminum Body, Wire Screen Arrestor

50445-5

0 to 50 ppm, Aluminum Body, Wire Screen Arrestor

50445-9

0 to 20 ppm, Aluminum Body, Wire Screen Arrestor

50448-1

0 to 100 ppm, Stainless Steel Body, Wire Screen Arrestor

50448-5

0 to 50 ppm, Stainless Steel Body, Wire Screen Arrestor

50448-9

0 to 20 ppm, Stainless Steel Body, Wire Screen Arrestor

51457-1L

0 to 100 ppm, Stainless Steel Body, Sintered Steel Arrestor

Operating Temperature

Range

CSA

ATEX/IECEx

Electronics

Division Classification

-40°F to 167°F (-40°C to 75°C)

Zone Classification

-40°F to 158°F (-40°C to 70°C)

-40°F to 140°F

(-40°C to 60°C)

-40°F to 158°F
(-40°C to 70°C)

Storage Temperature Range

-58°F to 185°F (-50°C to +85°C)

Operating Humidity Range

10% to 95% RH, non-condensing

Summary of Contents for Ultima MOS-5





































































Search results

Summary of Contents for Ultima MOS-5

Reviews:

Brands by name

Popular brands

MSA Ultima MOS-5, Instruction Manual

Search results

Summary of Contents for Ultima MOS-5

Reviews:

Brands by name

Popular brands