manualshive.com logo in svg

MSA Ultima MOS-5, Instruction Manual

Share
Download
MSA Ultima MOS-5 Instruction Manual Download Page 49

 

Ultima MOS-5 Detector

 

  

41 

   

8.8  Ultima MOS-5 Command Register Details 

8.8.1 Analog 

(00H) 

A read returns a value, which is proportional to the 0-20 mA output current. The current is 
based on a 16-bit value. The scaling is 0 - 65535 decimal, which corresponds to 0 - 21.7 mA.

 

8.8.2 Mode 

(01H) 

A read returns the present mode of the Ultima MOS-5 Intelligent Sensor.  

A write command changes the mode to the requested mode. A data value of 08 starts 
calibration mode if the unit is in the run mode.   It also goes from cal check to cal mode. 

Exception: Returns an exception code 01 (illegal function) if an illegal write is requested. 

A calibrate command returns an exception code 01 (Acknowledge 05). The operation will take 
a long time to complete. 

Function 

Bit Position 

Access 

Calibration Complete 

7 MSB 

Read 

Spanning 6 

Read 

Zero Complete, Waiting for Gas 

5 

Read 

Zeroing 4 

Read 

Calibration Mode 

3 

Read/Write 

Calibration Check Mode 

2 

Read/Write 

Run Mode 

1 

Read 

Startup Mode 

0 LSB 

Read 

8.8.3 Status/Error 

(02H) 

A read returns the alarm state and errors that are occurring at the present time, which are 
indicated, by bit position. 

Function 

Bit Position 

Access 

Alarm 15 

MSB 

Read 

Warn 14 

Read 

Fault 13 

Read 

Not Used 

12 

Read 

Not Used 

11 

Read 

Not Used 

10 

Read 

Not Used 

9 

Read 

Switch Error 

8 

Read 

Setup Error 

7 

Read 

Calibration Check Timeout 

6 

Read 

EEPROM Error 

5 

Read 

EPROM Error 

4 

Read 

Sensor Error 

3 

Read 

Fail to Calibrate 

2 

Read 

Low Supply Voltage 

1 

Read 

Summary of Contents for Ultima MOS-5





































































Reviews:

No comments

Brands by name

Popular brands

Load more brands